background image

6

IOM-C-CS

 

 

   

 Repair Parts

 

Item No. 

Description   

 Kit A     Kit B

 1 

  Body

 2 

  Spring 

Chamber

 4 

  Spring 

Button

 6 

Handle

 7 

Range 

Spring

 13 

Clamp 

1

 

14 Plug    

*

               14.1 

Stem 

 

 

 *

               14.2 

Seat 

 

 

 *

               14.3 

Tail Piece 

                  

 *

 15 

Gasket 

(Diaphragm) 

         *          *

 16 

O-ring 

(Plug) 

 

      *          * 

 17 

Diaphragm 

 

      *          *

 18 

O-ring 

 

      *          *

 19 

Seal 

 

 

      *          *

 20 

Pusher 

Plate

 21 

Hitch 

Pin

    1

 Refer to Figure 1 for Clamp and related item       

   numbers.

  

Item No.

 

Description   

 Kit A     Kit B

 

25 

Upper Guide Assembly

               25.6    

Adjusting Screw

               25.7    

Adjusting Screw Cap

               25.8    

Dowel Pin

               25.9    

Guide Seals (2 Req'd)   * 

*  

 26 

Bearing        

 27 

Guide 

Post

 28 

Pressure 

Plate

 

29 

Nut Hex Jam

 30 

Set 

Screw

 

Not Shown:
 Item No.

 

Description

 

11 Name 

Plate

 12 

Drive 

Screw

*   Recommended Spare Part

Figure 2

Barstock body

Metal Seat

Guide Seals

Composition Seat

Summary of Contents for C-CS










Reviews: