Case 1021G Service Manual Download Page 27

Page: 27 / 61

INTRODUCTION

Consumables

1021G Capacities and specifications

Engine

Type of oil

CASE AKCELA UNITEK NO. 1™ SBL CJ-4

Technical specifications

SAE 10W-40

API CJ-4

CASE CONSTRUCTION specifications

MAT3521

Type of oil

CASE AKCELA UNITEK NO. 1™ SSL CJ-4 SAE 0W-40

(cold weather)

Technical specifications

SAE 0W-40
API CJ-4

CASE CONSTRUCTION specifications

MAT3521

Capacity (with filter change)

28.5 l

(

30.1 US qt

)

Cooling system

Type of coolant

CASE AKCELA ACTIFULL™ OT EXTENDED LIFE
COOLANT

System capacity

56.8 l

(

60.0 US qt

)

Fuel system

System capacity

473.0 l

(

125.0 US gal

)

Hydraulic system

Type of fluid

CASE AKCELA HY-TRAN® ULTRACTION

Technical specifications

ISO VG-46

CASE CONSTRUCTION specifications

MAT 3540

Technical specifications

CASE AKCELA HY-TRAN® ULTRACTION SSL

(low temperature)

CASE CONSTRUCTION specifications

MAT 3541

Total system capacity

250.0 l

(

66.0 US gal

)

Reservoir capacity

134.0 l

(

35.4 US gal

)

Transmission

Type of oil

CASE AKCELA NEXPLORE™ FLUID

Service capacity - with filter change

45.4 l

(

48.0 US qt

)

Axles

Type of oil

CASE AKCELA TRANSAXLE FLUID 80W-140

Technical specifications

SAE 80W-140
API GL-4

CASE CONSTRUCTION specifications

MAT 3510

Front axle

42.0 l

(

44.4 US qt

)

Rear axle

42.0 l

(

44.4 US qt

)

Front axle with axle cooler

51.5 L

(

54.4 US qt

)

Rear axle with axle cooler

46.7 L

(

49.3 US qt

)

Heavy duty Front axle

62.0 l

(

65.5 US qt

)

Heavy duty Front axle with cooler

71.5 L

(

75.6 US qt

)

Heavy duty Rear axle

42.0 l

(

44.4 US qt

)

Heavy duty Rear axle with cooler

46.7 L

(

49.3 US qt

)

DEF/A

LUE

Technical specifications

ISO 22241-1

CASE CONSTRUCTION specifications

ES-BS001

Total capacity (*)

90.8 L

(

95.9 US qt

)

Grease fittings, as required

CASE AKCELA MOLY GREASE

CASE CONSTRUCTION specifications

MAT3550

Grade C

NOTICE:

(*) some liters always remain in the

DEF/A

LUE

reservoir. This allows for correct functioning of the wheel

loader components. DO NOT overfill the

DEF/A

LUE

tank. The tank is full when the

DEF/A

LUE

fluid level in

the tank reaches the bottom of the fill neck. Adequate air volume must be present in the top of the tank for proper
functionality of the after treatment system.

51428268_EN 19/12/2017

Summary of Contents for 1021G






























































Search results

Summary of Contents for 1021G

Reviews:

Related manuals for 1021G

Brands by name

Popular brands

Case 1021G, Service Manual

Search results

Summary of Contents for 1021G

Reviews:

Related manuals for 1021G

Brands by name

Popular brands