6
- Loosen the set off screws (H) using the Allen wrench (I)
- Slide the shoe (D) all the way back.
Curved cuts:
For sawing on a curve, use the special “curved cut” blade,
which is thin enough to saw along a curve.
Perforating wood (Fig 5):
To perforate wood, there are two possibilities:
1- Drill a hole and begin sawing from that point.
- Place the jig-saw on the rounded edge located at the
front of the bottom plate.
- Turn on the saw and slowly lower it until it touches the
material to be sawed.
- Once the material has been perorated, return the saw to
its normal position and continue sawing.
- Plunge cuts may only be applied to soft materials, such
as wood, gypsum board, etc. For plunge cuts, use only
short saw blades.
Dust extraction Assembly
- Connect dust extraction adaptor (K) on the appliance
- Connect the vacuum aspirator suction tube to the dust
extraction adaptor (K)
- Stop the appliance by releasing the on/off switch .
Cleaning
-
Disconnect the appliance from the mains and allow it to
cool before undertaking any cleaning task.
- Clean the electrical equipment and the mains connection
with a damp cloth and dry. DO NOT IMMERSE IN WATER
OR ANY OTHER LIQUID.
- Clean the equipment with a damp cloth with a few drops
of washing-up liquid and then dry.
- Do not use solvents, or products with an acid or base
pH such as bleach, or abrasive products, for cleaning the
appliance.
- Do not let water or any other liquid get into the air vents
to avoid damage to the inner parts of the appliance.
- Never submerge the appliance in water or any other
liquid or place it under running water.
- If the appliance is not in good condition of cleanliness, its
surface may degrade and inexorably affect the duration
of the appliance’s useful life and could become unsafe
to use.
Supplies
your appliance model.
- These supplies are available in specialist shops.
Anomalies and repair
- Take the appliance to an authorised technical support
service if a product damage or other problems arise. Do
not try to dismantle or repair without assistance, as this
may be dangerous.
- If the connection to the mains has been damaged, it
must be replaced and you should proceed as you would
in the case of damage.
Specifications:
SA650PEL
- Rated Power:
650W
- Rated Voltage:
230V~
- No load Speed
0-2800 rpm
- Wood cutting capacity
65 mm
- Steel cutting capacity
6 mm
- Aluminium cutting capacity
8 mm
- slant up to
45º
- Weight:
1.90 Kg
- Sound Pressure level
(LpA) = 83B(A), KpA = 3dB
- Sound Power level
(LwA) = 94dB(A), KWA = 3dB
- Instantaneous sound pressure level
(LpCpeak) = 96dB(C), KpCpeak = 3dB
- Vibration
6.38 m/s2, K=1.5 m/s2
notice of purpose of improvement.
-Measured sound level determined according EN60745
-The vibration emission level given in this information
sheet has been measured according EN60745 and may
be used to compare one tool with other. It may be used
for a preliminary assessment of exposure
-The vibration value during actual use of the power tool
can differ from the declared total value depending on the
way in which tool is used
-It’s necessary identify safety measures to protect the
operator that are based on an estimation of exposure in
the actual conditions of use (taking account of all parts
of the operating cycle such as the times when the tool is
switched off and when it is running idle in addition to the
trigger time).
For EU product versions and/or in case that it is re-
quested in your country:
Supplies
your appliance model.
- These supplies are available in specialist shops.
Anomalies and repair
- Take the appliance to an authorised technical support
service if a product damage or other problems arise. Do
not try to dismantle or repair without assistance, as this
may be dangerous.
- If the connection to the mains has been damaged, it
must be replaced and you should proceed as you would
in the case of damage.
Specifications:
- Rated Power:
- Rated Voltage:
- No load Speed
- Wood cutting capacity
- Steel cutting capacity
- Aluminium cutting capacity
- slant up to
- Weight:
- Sound Pressure level
(LpA) = 83B(A), KpA = 3dB
- Sound Power level
(LwA) = 94dB(A), KWA = 3dB
- Instantaneous sound pressure level
(LpCpeak) = 96dB(C), KpCpeak = 3dB
- Vibration
6.38 m/s2, K=1.5 m/s2
notice of purpose of improvement.
-Measured sound level determined according EN60745
-The vibration emission level given in this information
sheet has been measured according EN60745 and may
be used to compare one tool with other. It may be used
for a preliminary assessment of exposure
-The vibration value during actual use of the power tool
can differ from the declared total value depending on the
way in which tool is used
-It’s necessary identify safety measures to protect the
operator that are based on an estimation of exposure in
the actual conditions of use (taking account of all parts
of the operating cycle such as the times when the tool is
switched off and when it is running idle in addition to the
trigger time).
For EU product versions and/or in case that it is re
quested in your country:
Summary of Contents for SA650PEL
