Casablanca Modena II Owner'S Manual Download Page 3

3

M

odena

®

 II

INSTALLATION INSTRUCTIONS

IMPORTANT! Leave the fan in the carton until you are ready to hang the fan.

CEILING HARDWARE

GETTING STARTED

Installing a New Ceiling Fixture Outlet Box

If you do not have an existing fixture located where you 

wish to place your Casablanca fan, an approved ceiling 

fixture outlet box must be installed and wired.

After turning the power OFF at its source (either circuit 

breaker or fuse box), lower the old fixture and disconnect 

the wiring. Check the ceiling fixture outlet box to be sure 

that it is marked ‘Approved for ceiling fan mounting

’. 

If it is not, a new box must be installed. 

Warning: To reduce the risk of fire, electrical 

shock,  or  personal  injury,  mount  to  outlet  box 

marked acceptable for ceiling fan support using 

the mounting hardware provided with the outlet 

box. Using Existing Ceiling Fixture Outlet Box

CAUTION:  To  reduce  the  risk 
of personal injury, use only the 
mounting  hardware  provided 
with the approved outlet box to 
install  the  crossbar  mounting 
bracket.

CROSSBAR MOUNTING BRACKET INSTALLATION

Proceed with installation as follows:

Step 1.

 To install the crossbar mounting bracket, route 

the outlet box wires along side of the crossbar mounting 

bracket.  Attach  the  crossbar  mounting  bracket  to  the 

outlet box with the set of two round-head screws and 

washers.  Use  caution  when  installing  the  screws  and 

washers. Do not pinch the outlet box wires in the wash

-

ers. Tighten the screws firmly by hand only, being careful 

not to bend the bracket by over tightening.

Step  2.

  To  install  the  lag  screw,  slide  the  remaining 

washer onto the lag screw. Pass the lag screw through 

the center hole in the crossbar mounting bracket. Se-

cure the lag screw into the guide hole, tightening until 

the ceiling fixture outlet box is firmly mounted to the 

support beam.

CROSSbAR 

mOUNTINg 

bRACKET

WIRE NUT (4)

fLAT WASHER (2)

LAg SCREW AND WASHER  

(1)

1″

 x 8-32 ROUND 

HEAD SCREWS (2)

JOIST

CEILINg fIxTURE 

OUTLET bOx 

(CEILINg fAN 

RATED)

CROSSbAR 

mOUNTINg 

bRACKET

(RIDgE SIDE 

DOWN)

1” x 8-32 

ROUND-HEAD 

SCREWS (2)

WASHERS 

(2)

CEILINg 

WIRINg

gREEN 

gROUND 

WIRE

LAg SCREW 

AND 

WASHER (1)

Summary of Contents for Modena II












Reviews: