background image

2

Calculation of 32°

Use the tear-off 

Ceiling Angle Template

 card inserted in the 

back of this manual, it provides you with a simple ‘go’ or 

‘no-go’ for installing your fan on a sloped ceiling.

SLOpED CEILINg INSTALLATIONS

mOUNTINg RECOmmENDATIONS

7

 mINImUm

pole Length

Standard

Standard

6

12

12

18

24

36

48

Ceiling Height

8

8

 6

9

9

 6

10

11

 

12

 

13

 

14

Suggested Extension pole Lengths

When to Use Extension poles

For  best  performance  and  best  appear-

ance, an extension pole should be used 

with your Casablanca fan when installing 

on  high  (cathedral)  ceilings  or  sloped 

ceilings. Casablanca offers standard poles 

in increments of 6 up to 5

. Custom poles 

are  available  in  lengths  up  to  10

.  See 

your  Authorized  Casablanca  Dealer  for 

details.

32°

BLADES mUST BE 

A mINImUm OF 7

′ 

ABOVE THE FLOOR

EXTENSION 

pOLE

mAXImUm 

HANg-TRU® 

ANgLE 32º

Before mounting your Casablanca fan, read the following helpful recommendations. The location of the fan, air circulation, 

and fan size are all important factors to consider before installation.

Location

Ceiling fans have practical uses in almost every room in your home. We suggest you follow these mount-

ing recommendations as you decide where to install your Casablanca fan. 

•  For safety reasons, the fan blades must be a minimum of 7

 above the floor. 

•  Do not locate the fan in a doorway or above a swinging door. 

•  In any installation, the tips of the blades must be at least 18 from the wall in order to provide suf-

ficient clearance for the blades.

•  In bedrooms, fans work best when mounted above the foot of the bed.

•  Over pool tables, be sure to provide plenty of clearance to avoid damage from 

pool cues.

•  In low ceiling locations, our optional low ceiling adaptor (LCA)—available at 

extra cost—can be used to gain 3

1

/

2

.

•  In kitchens be sure to allow for open cupboard doors to clear the fan blades.

•  Do not install a fan close to, or over, a pool or spa. High humidity combined 

with corrosive gases will destroy the finish and warp the blades.

Fan Size

Variable fan speed capability permits the use of a full-size 52 fan even in 

smaller rooms. For very large rooms, two fans may be needed.

EXAmpLE 1

This slope is less than 32.

It is OK to install your fan.

EXAmpLE 2

This slope is 32.  This is the maximum slope 

that  will  allow  the  fan  to  hang  straight 

down.  It is OK to install your fan.

EXAmpLE 3

This slope is more than 32.

Your fan will not hang straight down, an 

adaptor  is  necessary.  Contact  your  local 

Authorized Casablanca Dealer in regards to 

purchasing a “Slope Ceiling Adaptor.”

note:

  Fan  may  wobble  or  vibrate  if 

pole  length  is  not  long  enough  and 

inside blade is too close to downslope 

or side wall. Extending pole length will 

usually solve problem.

A

urorA

 II

Summary of Contents for AURORA II













Reviews: