background image

IMPORTANT

MAX. 15 FT

MAX. 15 FT

CARVIN

®

 STARFALL| USER MANUAL

3

INSTALLATION

Before starting the installation of your skimmer & return, make sure you have all the 
necessary tools listed below. Check the contents in the box make sure everything 
is there before starting your installation. All parts included in the box are important 
and should all be installed. If parts are left out from the installation, this could cause 
serious failure of the skimmer and return. Once the installation is started, it should 
be completed as soon as possible. If a part is missing or defective, please contact 
your CARVIN

®

 retailer where your purchase was made.

TOOLS

•  Drill with screwdriver bit #3
•  Screwdriver bit #3 Phillips or Robertson
•  Small straight screwdriver
•   Hand saw

REQUIRED MATERIAL

•  Starfall 94114 XXX
•  A Star Series Starter kit, to power and control lights;

REQUIRED POOL EQUIPMENT

A basic circulation and filtration system MUST BE INSTALLED. This system includes 

the following products by installation order:

•   1 1/2’’ Flexible hose
•   PVC-ABS glue

The warranty of the product will be canceled if all installa-
tion requirements and guidelines are not respected.

WARNING

IMPORTANT TO CONSIDER BEFORE INSTALLING

1. Follow the installation steps thoroughly without omitting anything. It can result in 
  serious accidents.
2. Omitting installation steps may result in a leaking skimmer and/or leaking water 
return. Any leak could rust the wall and seriously damage the structure of your pool.

The manufacturer of your product has no responsibility for any omission of the 
installation steps contained in this manual or a non-compliant installation.

STARFALL INSTALLATION STEPS

STEP 2

Glue the Carvin quick connect fitting (included in box) on one end of the flexible 

hose.

DO NOT CUT THE FLEXIBLE HOSE, FINAL LENGTH WILL BE DETERMINED LATER.

STEP 3

For each selected position, remove the top ledge cover cap.

STEP 4

Unscrew the top ledge cover screw.

Your STARFALL will replace an actual ledge.

Keep in mind that further from the filter you install the 

STARFALL less performance your will have. 

We  recommand to stay in the next 3 top ledges from the 

filter for a maximum of 15 ft of hose.

 

STEP 1

Select the position where you want to install your STARFALL.

Summary of Contents for STARFALL










Reviews: