Carver pm700 User Manual Download Page 6

Power Output:

(20 Hz to 20kHz, with
no more than 0.1%)
325 watts per channel
into 8 ohms

475 watts per channel

into 4 ohms 
Bridged Mono: 
950 watts into 8 ohms
at 1kHz, with no more
than 0.1% THD 

Dynamic Headroom:

>2.0 dB

Frequency Response:

20Hz to 20kHz
(±0.75dB)

Channel Separation:

>65 dB @ 1kHz

Damping Factor:

<400 

Input Impedance:

25 Kohms unbalanced 
50 Kohms balanced 

Sensitivity:

High: 0.775V

RMS

for

rated power into 4
ohms 72mV

RMS

for 1W

into 4 ohms 
Low: 1.5 V

RMS

for rated

power into 4 ohms
140mV

RMS

for 1W into

4 ohms

Gain:

High: 35.0dB (±0.5 dB)
Low: 29.0dB (±0.5 dB)

Input Overload:

+18 dBu

THD:

< 0.1%

IM Distortion:

< 0.1%

Signal-to-Noise Ratio:

>100dB, A-weighted,
ref. to rated power into 
4 ohms 

Slew Rate:

40V / µS (Band 
width limited)

CMRR:

>80dB @ 1kHz

Power Consumption:

90W at idle; 725W with
musical program;
1370W at full power
into 8 ohms (continu-
ous); 2000W at full
power into 4 ohms
(continuous)

Power Requirements:

120VAC / 60Hz (USA
and Canada) Other
voltages as required for
export

Fusing:

12 amp slo-blo 
(120V / 60Hz) 8 amp 
slo-blo (230V / 50Hz)

Sequence Receive Terminal:

+7V to +15VDC 50mA
min. current require-
ment

Display:

7 LED indicators per
channel, 1 green
READY, 5 yellow SIG-
NAL, 1 red CLIP/ PRO-
TECT

Size (H x W x D):

3.50” (2U) x 19” x
13.25” 89

mm

x 483

mm

x 337

mm

Net Weight:

34 lbs. (15.4 kgs)

Shipping Weight:

36 lbs. (16.36 kgs)

Due to ongoing product development, 
features, specifications, and availability are
subject to change without notice.

5

pm950

325W per channel into 8 ohms
475W per channel into 4 ohms
950W mono into 8 ohms

XLR and 1/4” TRS input connectors

Accepts balanced or unbalanced lines

Multi-way Binding Post output connectors

Independent 11 detent Level Controls for CH1
and CH2

External Level Control Defeat Switch

Dual Mono mode for operating both channels
with 
a single mono input

Bridged Mono mode for combining the power of
both channels into a single higher powered chan-
nel

Input sensitivity set at 1.5V

RMS

from factory.

Internally  reconfigurable to 0.7775V

RMS

.

Internally configurable input polarity

Internal connection points for add-on accessories

Power ON Sequencer

Class H dual-rail power supply

Independent CH1 / CH2 Speaker relays will 
instantaneously disconnect if one of the following 
fault conditions is detected:

D.C. Offset
Over Temperature
Short Circuit

Additional protection circuitry includes:

Clipping Eliminator
AC Line Fuse

Power Connected / Standby indicator

7 LED display per channel, including Power 
Ready and Clip / Protect indicators

2-speed Fan cooled

70 volt / 100 volt transformer option

CE 1997 approved

4

NEXT

Summary of Contents for pm700





















Reviews: