Carver pm700 User Manual Download Page 5

pm700

225W per channel into 8 ohms
350W per channel into 4 ohms
700W mono into 8 ohms

XLR and 1/4” TRS input connectors

Accepts balanced or unbalanced lines

Multi-way Binding Post output connectors

Independent 11 detent level controls for 
CH1 and CH2 

External Level Control Defeat Switch

Dual Mono mode for operating both channels
with 
a single mono input

Bridged Mono mode for combining the power of
both channels into a single higher powered chan-
nel

Input sensitivity set at 1.5V

RMS

from factory.

Internally configurable to 0.775V

RMS

Internally configurable input polarity

Internal connection points for add-on accessories

Power ON Sequencer

Class H dual-rail power supply

Independent CH1 / CH2 Speaker relays will 
instantaneously disconnect if one of the following
fault conditions is detected:

D.C. Offset
Over Temperature
Short Circuit

Additional protection circuitry includes:

Clipping Eliminator
AC Line Fuse

Power Connected / Standby indicator

7 LED display per channel, including Power
Ready 

and Clip / Protect indicators

2-speed Fan cooled

70-volt / 100-volt transformer option

CE 1997 approved

2

Power Output::

(20Hz to 20kHz, with no
more than 0.1% THD)

225 watts per channel
into 8 ohms
350 watts per channel
into 4 ohms 
Bridged-mono:
700 watts into 8 ohms
at 1kHz, with no more
than 0.1% THD 

Dynamic Headroom:

>2.0dB

F requency Response:

20Hz to 20kHz (±0.75
dB)

Channel Separation:

>65dB @ 1kHz

Damping Factor:

<400 

Input Impedance:

25 Kohms unbalanced 
50 Kohms balanced

Sensitivity:

Low: 1.5 V

RMS

for

rated power into 4
ohms  160mV

RMS

for

1W into 
4 ohms
High: 0.775V

RMS

for-

rated power into 4
ohms 83mV

RMS

for 1W

into 4 ohms; 

Gain:

High: 33.8dB (±0.5dB)
Low: 27.8dB (±0.5dB)

Input Overload:

+18dB

THD:

<0.1%

IM Distortion:

<0.1%

Signal-to-Noise Ratio:

>100 dB, A-weighted,
ref. to rated power into

4 ohms 

Slew Rate:

40V / µS 
(Bandwidth limited)

CMRR:

>80dB @ 1kHz

Power Consumption:

55W at idle; 500W with
musical program;
1000W at full power
into 8 ohms (continu-
ous); 1550W at full
power into 4 ohms 
(continuous)

Power Requirements:

120VAC / 60Hz (USA
and Canada) Other
voltages as required
for export

Fusing:

10 amp slo-blo 
(120V / 60Hz) 7 amp 
slo-blo (230V / 50Hz)

Sequence Receive Terminal:

+7V to +15V DC

50mA min. current
requirement

Display:

7 LED indicators per
channel 1 green
READY, 5 yellow SIG-
NAL, 1 red CLIP /
PROTECT

Size (H x W x D):

3.50” (2U) x 19” x
13.25” 89

mm

x 483

mm

x 337

mm

Net Weight:

30 lbs. (13.6 kgs)

Shipping Weight:

36 lbs. (16.3 kgs)

Due to on-going product development, 
features, specifications, and availability are
subject to change without notice.

3

BACK

Summary of Contents for pm700





















Reviews: