background image

UNPACKING AND INSPECTION 

This appliance 
should be  
thoroughly 

cleaned prior to use.  
 
See the CLEANING         
INSTRUCTIONS  on 
page 6 in this manual. 

 
NOTE:  DO NOT 

discard 

the carton or other     
packing materials until 
you have inspected the 
appliance for hidden  
damage and checked it 
for proper operation.  
 
Refer to 

FREIGHT      

DAMAGE CLAIM          
PROCEDURE 

on            

bottom of this page. 

 

1.  Remove the cabinet from shipping carton, ensuring that all packing mate-

rials and protective plastic have been removed from the unit.  

2.  Inspect all components for completeness and condition. 

 

- Pan covers: these may be polycarbonate plastic with metal springs or 

 

metal, depending on which model you have. There should be one lid for 

 each 

cabinet 

cavity. 

 

 

- Pans (if ordered) 

1.  If any freight damage is present, a freight claim must be filed immediately 

with the shipping company.   

2. 

Freight damage is not covered under warranty

.  

3.  Check to insure all components are included: cabinet, instruction packet 

and additional accessories: amber water reservoir, stainless steel water 
trough. 

4.  Read operation instructions completely. 

5.  Appliance should be thoroughly cleaned before use.  See CLEANING 

INSTRUCTIONS on page 6 in this manual. 

FREIGHT DAMAGE PROCEDURE 

 

NOTE:  

For your protection, please note that equipment in this shipment was carefully inspected and packaged by 

skilled personnel before leaving the factory.  Upon acceptance of this shipment, the transportation company assumes 
full responsibility for its safe delivery. 

 

IF SHIPMENT ARRIVES DAMAGED: 

1. 

VISIBLE LOSS OR DAMAGE: 

Be certain that any visible loss or damage is noted on the freight bill or express re-

ceipt, and that the note of loss or damage is signed by the delivery person. 

2. 

FILE CLAIM FOR DAMAGE IMMEDIATELY:  

Regardless of the extent of damage. 

Contact your dealer immedi-

ately.

 

3. 

CONCEALED DAMAGE:

  If damage is unnoticed until the merchandise is unpacked, notify the transportation com-

pany or carrier immediately, and then file a “CONCEALED DAMAGE” claim with them.  This should be done within 
fifteen (15) days from the date the delivery was made to you.  

Be sure to retain the container for inspection

 

Carter-Hoffmann cannot assume liability for damage or loss incurred in transit, 

freight damage is not covered under 

warranty

. We will, however, at your request, supply you with the necessary documents to support your claim.

    

 

GROUNDING INSTRUCTIONS

 

This appliance is equipped with a cord having a grounding wire with a grounding plug which must be plugged into an 
outlet that is properly installed and grounded.  In the event of an electrical short circuit, grounding reduces the risk of 
electric shock by providing an escape wire for the electric current.   
 

WARNING—Improper use of the grounding can result in a risk of electric shock.

  Consult a qualified electrician or 

service agent if the grounding instructions are not completely understood, or if doubt exists as to whether the appliance 
is properly grounded. 

Summary of Contents for MC112S-2T













Reviews: