background image

Page 4 of 12 

SA-500-27 14   Installation and Operating Instructions 

09/09/08 

CP5015A 

 

INSTALLATION 

Proper installation of the unit is essential for years of safe, reliable operation.  Please read all 
instruction 

before

 installing the unit.  Failure to follow these instructions can cause serious dam-

age to the unit or vehicle and may void warranties. 

SAFETY PRECAUTIONS 

For the safety of the installer, vehicle operator, passengers and the community please observe 
the following safety precautions.  

Failure to follow all safety precautions and instructions may 

result in property damage, injury or death.

 

Qualifications - 

The installer must have a firm knowledge of basic electricity, vehicle electrical 

systems and emergency equipment. 

Mounting

 - Mount the unit for easy access by the vehicle operator.  DO NOT mount in air bag 

deployment area.  Assure clearances before drilling in vehicle.  To prevent internal damage 
mounting bolts must not enter case more than 1/4". 

Wiring

 - Use wiring capable of handling the current required.  Make sure all connections are tight.  

Route wiring to prevent wear, overheating and interference with air bag deployment.  Install and 
check all wiring before connection to vehicle battery. 

Testing

 - Test all siren functions after installation to assure proper operation.  Test vehicle opera-

tion to assure no damage to vehicle. 

Keep These Instructions

 - Keep these instructions in the vehicle or other safe place for future 

reference.  Advise the vehicle operator of the location. 
 
 
 
 
 
 

UNPACKING 

Inspect contents for shipping damage.  If found 

alert carrier immediately

Contact supplier immediately if any components are missing. 
Contents of box should include the following items: 

 

Qty Item 

1  Amplifier Unit with attached Microphone   (SA-500-27 14) 
1  Bracket, ‘U’ Dash Mount   (CP3571) 
1  Hardware Kit   (ED1558) 

(Kit contains 2 Bolts, 1  10-P Term Block Plug, and 1 Mic Clip) 

1  Instruction Manual   (CP5015   This Manual) 

Sound Hazard

 - Sound level from siren speaker (>120dBA @ 10 feet) may cause hearing damage. 

Do not operate siren without adequate hearing protection for you and anyone in immediate vicinity. 
(Ref. OSHA 1910.95 for occupational noise exposure guidelines) 

Summary of Contents for SA-500-27













Reviews: