background image

1

50VR---A and 50VR---C

Performance

t

15 SEER 2---Stage Packaged Heat Pump

System with Puron

(R---410A) Refrigerant

Single and Three Phase

2---5 Nominal Tons (Sizes 24---60)

Installation Instructions

IMPORTANT

: Effective January 1, 2015, all split system and

packaged air conditioners must be installed pursuant to applicable
regional efficiency standards issued by the Department of Energy.

NOTE

:

Read the entire instruction manual before starting the

installation.

NOTE

:

Installer: Make sure the Owner’s Manual and Service

Instructions are left with the unit after installation.

TABLE OF CONTENTS

PAGE

SAFETY CONSIDERATIONS

1

. . . . . . . . . . . . . . . . . . . . . . . . .

INTRODUCTION

2

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

RECEIVING AND INSTALLATION

2--10

. . . . . . . . . . . . . . . . .

Check Equipment

2

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Identify Unit

2

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Inspect Shipment

2

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Provide Unit Support

2

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Roof Curb

2

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Slab Mount

2

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Provide Clearances

6

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Field Fabricate Ductwork

6

. . . . . . . . . . . . . . . . . . . . . . . . . . . .

Rig and Place Unit

6

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Inspection

7

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Rigging/Lifting of Unit

7

. . . . . . . . . . . . . . . . . . . . . . . . . . . .

Connect Condensate Drain

7

. . . . . . . . . . . . . . . . . . . . . . . . . . .

Install Duct Connections

7

. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Configuring Units for Downflow (Vertical) Discharge

8

. . . .

Install Electrical Connections

8

. . . . . . . . . . . . . . . . . . . . . . . . .

High--Voltage Connections

9

. . . . . . . . . . . . . . . . . . . . . . . . .

Special Procedures for 208v Operation

9

. . . . . . . . . . . . . . . .

Control Voltage Connections

9

. . . . . . . . . . . . . . . . . . . . . . . .

Standard Connection

9

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Transformer Protection

9

. . . . . . . . . . . . . . . . . . . . . . . . . . . .

PRE--START--UP

11

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

START--UP

11--13

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Check Cooling and Heating Control Operation

11

. . . . . . . . . .

Check for Refrigerant Leaks

11

. . . . . . . . . . . . . . . . . . . . . . . . .

Start--Up Adjustments

12

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Checking and Adjusting Refrigerant Charge

12

. . . . . . . . . . .

Indoor Airflow and Airflow Adjustments

12

. . . . . . . . . . . . .

Low Stage Cooling

13

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

High Stage Cooling

13

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

High Stage Enhanced Dehumidification Cooling (208/230 Vac
Models)

13

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Continuous Fan

13

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Sequence of Operation

13

. . . . . . . . . . . . . . . . . . . . . . . . . . .

Defrost Control

13

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Quiet Shift

13

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Defrost

13

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

MAINTENANCE

32--35

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Air Filter

32

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Indoor Blower and Motor

32

. . . . . . . . . . . . . . . . . . . . . . . . .

Outdoor Coil, Indoor Coil, and Condensate Drain Pan

33

. . .

Outdoor Fan

33

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

A09033

Fig. 1 -- Unit 50VR

Electrical Controls and Wiring

33

. . . . . . . . . . . . . . . . . . . . .

Refrigerant Circuit

34

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Evaporator Airflow

34

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Metering Device

34

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

System Information

35

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Loss of Charge Switch

35

. . . . . . . . . . . . . . . . . . . . . . . . . . . .

Check Defrost Thermostat

35

. . . . . . . . . . . . . . . . . . . . . . . . .

TROUBLESHOOTING

35

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

START--UP CHECKLIST

35

. . . . . . . . . . . . . . . . . . . . . . . . . . . .

SAFETY CONSIDERATIONS

Improper installation adjustment, alteration, service, maintenance,
or use can cause explosion, fire, electrical shock, or other

conditions which may cause death, personal injury, or property
damage. Consult a qualified installer, service agency, or your

distributor or branch for information or assistance. The qualified

installer or agency must use factory--authorized kits or accessories
when modifying this product Refer to the individual instructions

packaged with the kits or accessories when installing.
Follow all safety codes. Wear safety glasses, protective clothing,

and work gloves. Use quenching cloth for brazing operations.

Have a fire extinguisher available. Read these instructions
thoroughly and follow all warnings or cautions included in

literature and attached to the unit. Consult local building codes, the
current editions of the National Electrical Code (NEC) NFPA 70.

In Canada refer to the current editions of the Canadian electrical

Code CSA C22.1.
Recognize safety information. This is the safety--alert symbol

.

When you see this symbol on the unit and in instructions or

manuals, be alert to the potential for personal injury. Understand
these signal words; DANGER, WARNING, and CAUTION. These

words are used with the safety--alert symbol. DANGER identifies
the most serious hazards which

will

result in severe personal injury

or death. WARNING signifies hazards which

could

result in

personal injury or death. CAUTION is used to identify unsafe
practices which

may

result in minor personal injury or product and

property damage. NOTE is used to highlight suggestions which

will

result in enhanced installation, reliability, or operation.

Summary of Contents for Performance 50VR-A







































Reviews: