background image

Thermistor, Immersion

 

Installation and Operation

 

 

 

#NSA-A/CP-I-2.5-4X, NSA-A/CP-I-4-4X, NSA-A/CP-I-6-4X, NSA-HH/CP-I-2.5-PB-C, NSA-HH/CP-I-4-PB-C 
NSA-HH/CP-I-6-PB-C 

– 11/15/2019 

 

Specifications subject to change without notice. 

Catalog No. 11-808-785-01 

Page 

1

 of 

5

 

Overview 

 

Carrier Immersion Thermistors provide a predictable and accurate output over the specified 
temperature range. Each sensor configuration is designed and manufactured for long-term 
quality and performance. Carrier incorporates standard features such as double encapsulation 
and etched Teflon leads where applicable. 

 

 

 

 

 

Part Numbers 

 

NSA-A/CP-I-2.5-4X 

NSA-A/CP-I-4-4X 

NSA-A/CP-I-6-4X 

NSA-HH/CP-I-2.5-PB-C 

NSA-HH/CP-I-4-PB-C 

NSA-HH/CP-I-6-PB-C 

 

 

Specifications 

 

Number Sensing Points: 

One 

Storage Temperature Range: 

-40 to 85 °C (-40 to 185 °F) 

Operating Humidity Range: 

0 to 90% RH, non-condensing 

Probe Diameter | Thermowell Bore Diameter: 

0.250” (6.35mm) | 0.260” 

Probe Material | Thermowell Material: 

304 Stainless Steel | 304 Series Stainless Steel 

Wire Size 

22 AWG (0.65 mm) 

Thermowell Instrument | Process Thread Size: 

½” NPS (National Pipe Straight) Female Thread | ½” NPT (National Pipe 
Tapered) Male Thread 

Enclosure Specifications 
(Temperature, Material, 
Flammability, NEMA/IP Ratings) 

“-PB” Enclosure

: ABS Plastic, UL94-HB, -30 to 90 °C (-22 to 194 °F), 

Plenum Rated 

“-4X” Enclosure

: Polystyrene Plastic, UL94-V2, -40 to 70°C (-40 to 158°F), 

NEMA 4X (IP 66) 

Sensor Output @ 25 °C (77 °F):  
(Lead Wire Colors) 

10 KΩ nominal (White/Green) 

Immersion Length 

NSA-xxx-2.5

2.5” (63.50 mm) | 

NSA-xxx-4

4.0“ (101.60 mm) 

NSA-xxx-6

6.25” (158.75 mm) 

Probe Length 

NSA-xxx-2.5

4.31” (109.47 mm) +/- 0.13” (3.30 mm) 

NSA-xxx-4

: 5.81“ (147.57 mm) +/- 0.13” (3.30 mm) 

NSA-xxx-6

: 7.81” (198.37 mm) +/- 0.13” (3.30 mm) 

 

 

 

Summary of Contents for NSA-A/CP-I-2.5-4X






Reviews: