background image

 

LEVEL UNIT 

To provide adequate condensate drainage and 
proper door alignment and operation of unit, the 
unit cabinet must be level. Leveling feet are 
factory installed. Remove the front grille to gain 
access to front and back feet. 

  TO GAIN ACCESS TO LEVELING 

FEET 

U

   DANGER 

Before servicing unit, disconnect electrical 
service. Failure to disconnect electrical service 
could result in electrical shock and cause 
personal injury or death. 

 

1. 

After disconnecting the unit from the power 

supply, remove the grille retaining screw 
located in the upper-most part of the grille. 
(See Figure 2) 

2. 

Lift the grille up and away from the unit. 

3. 

Unplug the power supply cord located at the 

bottom of the cabinet. (See Figure 3) 

 

 

 

FIGURE 2 – REMOVE FRONT GRILLE 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

FIGURE 3 – DISCONNECT SERVICE CORD 

 

  TO LEVEL UNIT 

U

   DANGER 

Before servicing unit, disconnect electrical 
service. Failure to disconnect electrical service 
could result in electrical shock and cause 
personal injury or death. 

 

Swing Doors- The door is equipped with gravity 
assisted cams and will not function properly 
without proper leveling of cabinet. Adjust feet 
using adjustable wrench so that unit sits 
approximately level to floor and doors close 
properly. For best door operation, adjust leveling 
feet so that cabinet has a 

1

/

16

-in. rake or slant from 

front to back. Optional casters are available to 
replace leveling feet. 

Sliding Doors- The door will not function properly 
without proper leveling of cabinet. Adjust feet 
using adjustable wrench so that unit sits 
approximately level to floor and doors close 
properly.  

NOTE: If casters are not used, local codes may 
require cabinet to be sealed around the perimeter 
of the cabinet base. Consult local sanitation codes. 
Use only sealant material approved for this use, 
such as Dow Corning #732. 

Summary of Contents for Miracool















Reviews: