background image

Manufacturer reserves the right to discontinue, or change at any time, specifications or designs without notice and without incurring obligations.

Catalog No. 04-53360009-01

Printed in U.S.A.

Form 36S-1SI

Pg 1 

9-18

Replaces: 36R,S-1SI

Installation Instructions 

CONTENTS

GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   1

VERTICAL UNIT INSTALLATION  . . . . . . . . . . . . . . 2

Step 1 — Install Wall Mounting Strip and Hang Base

Unit  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Step 2 — Make Air Connections   . . . . . . . . . . . . . . 2

Step 3 — Connect Piping  . . . . . . . . . . . . . . . . . . .   3

Step 4 — Install Accessory Grilles (If Supplied,

 on Furred-In or Custom 
Enclosure Installations)  . . . . . . . . . . . . . . . . . .   3

Step 5 — Install Carrier Enclosures   . . . . . . . . . . . 3

Step 6 — Install Stiffener Brackets for Enclosure

Runouts  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Step 7 — Install Enclosure and Runout Arrange-

ment As Required  . . . . . . . . . . . . . . . . . . . . . . . . 4

• COLUMN-TO-COLUMN ARRANGEMENT
• COLUMN-TO-COLUMN WITH SHELVING
• ENCLOSURE WITH SINGLE OR DUAL RUNOUT 
• SINGLE OR DUAL RUNOUT WITH KICKSTRIP 

Step 8 — Balance System   . . . . . . . . . . . . . . . . . .   6

HORIZONTAL UNIT INSTALLATION 

(Unit-Mounted or Wall-Mounted 
Thermostat)  . . . . . . . . . . . . . . . . . . . . . . . . . . . .   7

Base Unit Not in Carrier Enclosure  . . . . . . . . . . . . 7

Base Unit in Carrier Enclosure   . . . . . . . . . . . . . . . 7

Coil Reversal  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

GENERAL

These units are controlled by varying water flow through coil.

Follow installation steps in sequence suggested. Each step in-

cludes figure(s) and procedures required for a specific stage

of installation.
Set up a sample installation to familiarize all trades with their

specific job function.
See  Fig.  1  for  the  Proposition  65  warning  label.  See  Fig.  2

and 3 for 36SV,SL base units.

Fig. 1 — Proposition 65 Warning Label

Fig. 2 — 36SV Base Unit

!

!

!

WARNING

AVERTISSEMENT

ADVERTENCIA

This product can expose you to chemicals
including Acrylonitrile, which is known to the 
State of California to cause cancer. For 
more information, go to 
www.P65Warnings.ca.gov

Ce produit peut vous exposer à des 
agents chimiques, y compris l’acrylonitrile,
que l’État de Californie reconnaît comme
cancérigènes. Pour plus d’informations,
veuillez consulter
www.P65Warnings.ca.gov 

Este producto puede exponerlo a productos
químicos que incluyen acrilonitrilo, que
el estado de California considera que 
causa cáncer. Para más información visite
www.P65Warnings.ca.gov

RETURN

SUPPLY

CONDENSATE
PAN

PRIMARY AIR INLET

36S

Induction Air Terminals

(Bypass and Water Control)

Summary of Contents for INDUCTION AIR TERMINALS 36S









Reviews: