9
3 — Without Unlock Code
The entire keypad will be locked. When the user presses a but-
ton, the backlight turns on to maximum brightness for 10 sec-
onds but none of the thermostat operating parameters will be
changed. The padlock icon will be on until the user presses and
holds the UP and DOWN buttons simultaneously for five sec-
onds to unlock the keypad. Once the keypad is unlocked, the
user has full access to the thermostat functionality. The keypad
returns to the locked condition after no buttons have been
pressed for two minutes.
3 — With Unlock Code
The thermostat will be completely locked and the padlock icon
will be on steady. Once the unlock code has been entered and the
DONE button has been pressed, the padlock icon flashes and
the thermostat functionality will operate as described above in
the "3 — Without Unlock Code" description.
cd — Code Only
The entire keypad will be locked and the padlock icon will be
displayed. When the user presses a button the backlight will
turn on to maximum brightness for 10 seconds and a “- --” will
be shown in the clock display. The user enters the unlock code
and press the DONE button to unlock the thermostat. The pad
lock icon will turn off and the user will have full access to the
thermostat functionality. The thermostat will lock after no but-
tons have been pressed for two minutes.
NOTES:
• The keypad will not lock if the thermostat is operating in
configuration mode or test mode.
• When the user exits from configuration mode, the ther-
mostat keypad will lock immediately if the keypad lock-
out level is set to anything other than off.
Unlocking Keypad with Access Code — When the keypad is
locked and a lockout code is required, pressing any button on the
keypad will display the lockout code as “
- --
” in the time display.
Press an UP or DOWN arrow key to change the dashes to the ac-
cess code. When the correct 4-digit lockout code is displayed,
press the DONE button.
In the event that the installer or user cannot remember the un-
lock code for the thermostat, the code can be displayed if the
user presses and holds the soft key below the days of the week
and the soft key below the cooling set point simultaneously for
30 seconds. After the 30-second period, the unlock code will be
displayed for five seconds. This information does not appear in
any user documentation.
The default is OF (off).
OPTION 22 — HIGH COOL LATCH TEMPERATURE —
An outdoor sensor is required for high cool latch feature and
Option 7 (Equipment DDC Controller) has to be set to OF (off).
This selection is not available if the equipment DDC has been
set to On. Configuration settings are OF (off), 80, 85, 90, 95,
100, 105, 110 F (26.7, 29.4, 32.2, 35, 37.8, 40.5, 43.3 C) and On.
When set to OF (off), cooling always starts in low stage (Y1)
and stages up to high stage (Y1 and Y/Y2) when demand is suf-
ficient and staging timer constraints have been satisfied.
When set to 80 through 110 F (26.7 through 43.3 C), this is
the outdoor temperature above which both first and second stag-
es of the compressor are energized to satisfy all cooling de-
mands. When a cycle starts under a high cool latch, it will finish
the cooling cycle on high stage. If the cooling equipment is ener-
gized to satisfy a dehumidification demand only (no cooling de-
mand), the latch will not be applied.
When set to On, the Y1 and Y/Y2 outputs are simultaneously
energized to satisfy all cooling demands.
The default is OF (off).
OPTION 23 — HIGH HEAT LATCH TEMPERATURE —
This selection is only available when Option 1 is set to HP and
Option 7 (equipment DDC controller) is set to OF (off).
Configuration settings are OF (off), 20, 25, 30, 35, 40, 45,
50 F (–6.7, –3.9, –1.1, 1.7, 4.4, 7.2, 10 C) and On.
When set to OF (off), heating always starts in low stage (Y1)
and stages up to high stage (Y1 and Y/Y2) when demand is suf-
ficient and staging timer constraints have been satisfied.
When set to 20 through 50 F (-6.7 through 10 C), this is the
outdoor temperature below which both first and second stages of
the compressor are energized to satisfy all heating demands.
When a cycle starts under a high heat latch, it will finish the heat-
ing cycle on high stage.
When set to On, the Y1 and Y/Y2 outputs are simultaneously
energized to satisfy all heating demands.
The default is OF (off).
OPTION 24 — PROGRAMMABLE/NON-PROGRAMMA-
BLE
— This selection allows the installer to configure the ther-
mostat as either programmable (P) or non-programmable (nP).
Selections are P and nP. The default is P.
NOTE: If non-programmable is chosen, then the fan will run
only when there is a call for heating or cooling (fan auto).
OPTION 25 — NUMBER OF PROGRAMMABLE PERI-
ODS PER DAY — This selection allows the installer to con-
figure the thermostat for two or four periods per day. This selec-
tion is not available if Option 24 has been set to nP to configure
the thermostat for non-programmable operation.
When set to 2, periods OCC and UNOCC are available.
When set to 4, periods OCC, OCC2, OCC3 and UNOCC are
available.
The default is 4.
OPTION 26 — MINIMUM COOLING SET POINT — This
selection allows the installer to configure the minimum cooling
set point that the user is allowed to set. The range takes into
account the value of the adjustable deadband Option 11. The
range is 50 to 90 F (10 to 32.2 C) plus the deadband. The default
is 55 F (12.8 C) (based on the adjustable deadband default of 5 F
or 2.8 C).
OPTION 27 — MAXIMUM HEATING SET POINT — This
selection allows the installer to configure the maximum heating
set point. The range is based on the adjustable deadband value
Option 11. The range is 50 F to 90 F (10 to 32.2 C) minus the
deadband.
The default is 85 F (29.4 C) (based on the adjustable dead-
band default of 5 F or 2.8 C).
OPTION 28 — UV LIGHT REMINDER — This selection al-
lows the installer to select the number of months after which the
UV Light icon will be displayed to indicate to the user
that it is
time to call the contractor to have the UV light(s) replaced. Se-
lections available are OF (off), 6, 12, 18, 24, 30, 36, 42, and 48.
When set to OF (off), the UV light reminder is turned off and
will never be displayed.
When set to 6 through 48, this is the number of months after
which the UV light reminder will be displayed.
The default is OF (off).
OPTION 29 — SERVICE REMINDER — This selects the
number of months after which the service icon will be displayed.
When set to OF (off), the service reminder is disabled and
will never be displayed.
When set to 1 through 24, this is the number of months after
which the service icon will be displayed.
The default is OF (off).
OPTION 30 — UNUSED
OPTION 31 — DAYLIGHT SAVINGS TIME CONFIGU-
RATION — This selection allows the installer to set the thermo-
stat to automatically change by one hour on the specified day-
light savings day, month, and week.
Summary of Contents for EDGE Pro
Page 27: ......
