background image

19

Table 11 — Menu Structure

MENU

PARAMETER

PARAMETER

DEFAULT

VALUE

PARAMETER

RANGE AND 

INCREMENT

2

NOTES

STATUS

ECON AVAIL

NO

YES/NO

ECONOMIZING AVAILABLE

YES = economizing available; the system can use outside air for free cooling 

when required

ECONOMIZING

NO

YES/NO

ECONOMIZING ACTIVE

YES = Outside air being used for 1st stage cooling

NO = Economizing not active

OCCUPIED

NO

YES/NO

OCCUPIED

YES = OCC signal received from space thermostat or unitary controller

YES = 24 vac on terminal OCC.

NO = 0 vac on terminal OCC.

HEAT PUMP

n/a

COOL

HEAT

HEAT PUMP MODE

(Not available on 2-speed configuration)

COOL Y1-IN

OFF

ON/OFF

FIRST STAGE COOLING DEMAND (Y1-IN)

Y1-I signal from space thermostat or unitary controller for cooling stage 1.

ON = 24 vac on terminal Y1-I

OFF = 0 vac on terminal Y1-I

COOL Y1-OUT

OFF

ON/OFF

FIRST STAGE COOLING RELAY OUTPUT

ON = 24 vac on terminal Y1-O; Stage 1 mechanical cooling called on

OFF = 0 vac on terminal Y1-O; no mechanical cooling

COOL Y2-IN

OFF

ON/OFF

SECOND STAGE COOLING DEMAND (Y2-IN)

Y2-I signal from space thermostat our unitary controller for second stage 

cooling.

ON = 24 vac on terminal Y2-I

OFF = 0 vac on terminal Y2-I

COOL Y2-OUT

OFF

ON/OFF

SECOND STAGE COOLING RELAY OUTPUT

ON = 24 vac on terminal Y2-O; stage 2 mechanical cooling called on

OFF = 0 vac on terminal Y2-O; no stage 2 mechanical cooling

MA TEMP

_ _ . _°F (or °C) 0°F to 140°F

(–18°C to 60 °C)

MIXED AIR TEMPERATURE, Cooling Mode

Displays value of measured mixed air from MAT sensor. Displays _ _ . _  if 

not connected, short or out-of-range.

DA TEMP

_ _ . _°F (or °C) 0°F to 140°F

(–18°C to 60 °C)

DISCHARGE AIR TEMPERATURE, after Heating section

(Accessory sensor required)

Displays when Discharge Air sensor is connected and displays measured 

discharge temperature. Displays _ _ . _ if sensor sends invalid value, if not 

connected, short or out-of-range.

OA TEMP

_ _ . _°F (or °C) –40°F to 140°F

(–40°C to 60°C)

OUTSIDE AIR TEMPERATURE

Displays measured value of outdoor-air temperature. Displays _ _ . _ if 

sensor sends invalid value, short or out-of-range.

OA HUM

_ _%

0 to 100%

OUTSIDE AIR RELATIVE HUMIDITY

Displays measured value of outdoor humidity from OA sensor. Displays __% 

if not connected, short, or out-of-range.

RA TEMP

_ _ . _°F (or °C) 0°F to 140°F

(–18°C to 60°C)

RETURN AIR TEMPERATURE

Displays measured value of return air temperature from RAT sensor. 

Displays _ _ . _ if sensor sends invalid value, if not connected, short or out-

of-range

RA HUM

_ _%

0 to 100%

RETURN AIR RELATIVE HUMIDITY

Displays measured value of return air humidity from RA sensor. Displays 

__% if sensor sends invalid value, if not connected, short or out-of-range

IN CO2

_ _ _ppm

0 to 2000 ppm

SPACE/RETURN AIR CO

2

(CO

2

 sensor required, accessory or factory option)

Displays value of measured CO

2

 from CO

2

 sensor. Invalid if not connected, 

short or out-of-range

DCV STATUS

n/a

ON/OFF

DEMAND CONTROLLED VENTILATION STATUS

(CO

2

 sensor required, accessory or factory option)

Displays ON if above set point and OFF if below set point, and ONLY if a 

CO

2

 sensor is connected.

DAMPER OUT

2.0V

2.0 to 10.0-v

Displays voltage output to the damper actuator.

0% = OA Damper fully closed

100%= OA Damper full open

ACT POS

_ _%

0 to 100%

Displays actual position of outdoor air damper actuator

2.0-v = OA Damper fully-closed

10.0-v = OA Damper full open

ACT COUNT

n/a

1 to 65535

Displays number of times actuator has cycled.

1 cycle equals accrued 180° of actuator movement in any direction

ACTUATOR

n/a

OK/Alarm

(on Alarm menu)

Displays Error if voltage or torque is below actuator range

EXH1 OUT

OFF

ON/OFF

EXHAUST STAGE 1 RELAY OUTPUT

Output of EXH1 terminal:

ON = relay closed

OFF = relay open

EXH2 OUT

OFF

ON/OFF

EXHAUST STAGE 2 RELAY OUTPUT

Output of AUX terminal; displays only if AUX = EXH2

ON = relay closed

OFF = relay open

Summary of Contents for CRECOMZR077A00





























Reviews: