background image

Section 1 — General Information

15 kW Generator

 6 

1.6   SPECIFICATIONS

1.6.1 GENERATOR

Rated Max. Cont. Power Capacity (Watts*) .....  13,000 NG/

15,000 LP†

Rated Voltage....................................................... 120/240
Rated Max. Continuous Load Current (Amps)
  120 Volts + ......................................108.3 NG/125.0 LP
  240 Volts ..............................................54.2 NG/62.5 LP
Main Line Circuit Breaker ....................................65 Amp
Phase ............................................................................. 1
Number of Rotor Poles ................................................... 2
Rated AC Frequency ................................................60 Hz
Power Factor .................................................................. 1
Recommended Air Filter ...........................Part # 0C8127
Battery Requirement at 
-17.8° C (0° F) .......................  Group 26/26R 12 Volts and

525 Cold-cranking Amperes Minimum

Weight ........................................................... 487 Pounds
Output Sound Level @ 23 ft (7m)
  at full load ................................................... 71.5 db (A)
Normal Operating Range ...........................  -20°F (-28.8°C)

to 104°F (40°C)

*  Maximum wattage and current are subject to and limited by such factors 

as fuel Btu content, ambient temperature, altitude, engine power and con-
dition, etc. Maximum power decreases about 3.5 percent for each 1,000 
feet above sea level; and also will decrease about 1 percent for each 6° C 
(10° F) above 16° C (60° F).

+  Total current in two separate circuits. Current in each circuit must not 

exceed the value stated for 240V.

1.6.2 ENGINE

Type of Engine ......................................................GT-990
Number of Cylinders ...................................................... 2
Rated Horsepower .................................. 30 @ 3,600 rpm
Displacement ..........................................................992cc
Cylinder Block .....................Aluminum w/Cast Iron Sleeve
Valve Arrangement ..................................Overhead Valves
Ignition System .............................. Solid-state w/Magneto
Recommended Spark Plug ...................................0D4529
Spark Plug Gap ............................0.508 mm (0.020 inch)
Compression Ratio ................................................... 9.5:1
Starter .................................................................... 12Vdc
Oil Capacity Including Filter.................... Approx. 1.7 Qts
Recommended Oil Filter ........................... Part # 070185
Recommended Air Filter ...........................Part # 0C8127
Operating RPM ........................................................ 3,600

‹

‹

1.7  

FUEL REQUIREMENTS 
AND RECOMMENDATIONS

With LP gas, use only the vapor withdrawal sys-
tem.

 This type of system uses the vapors formed 

above the liquid fuel in the storage tank.

The engine has been fitted with a fuel carburetion 
system that meets the specifications of the 1997 
California Air Resources Board for tamper-proof 
dual fuel systems. The unit will run on natural gas or 
LP gas, but it has been factory set to run on natural 
gas. Should the primary fuel need to be changed to 
LP gas, the fuel system needs to be reconfigured. See  
instructions in the “Reconfiguring the Fuel System” 
section.

Recommended fuels should have a Btu content of at 
least 1,000 Btus per cubic foot for natural gas; or at 
least 2,520 Btus per cubic foot for LP gas. Ask the 
fuel supplier for the Btu content of the fuel.

Required fuel pressure for 

natural gas is 5 inches 

to 7 inches water column (0.18 to 0.25 psi); and 
for liquid propane, 11 inches to 14 inches of water 
column (0.4 to 0.5 psi).

NOTE:

Any piping used to connect the generator to the 
fuel supply should be of adequate size to ensure 
the fuel pressure NEVER drops below 4 inches 
water column for natural gas or 10 inches water 
column for liquid propane for all load ranges.

1.8 FUEL 

CONSUMPTION

* Natural gas is in cubic feet per hour.
** LP is in gallons per hour/cubic feet per hour.
*** Values given are approximate.

  Gaseous fuels such as natural gas and liquid 

propane (LP) gas are highly explosive. Even the 
slightest spark can ignite such fuels and cause 
an explosion. No leakage of fuel is permitted. 
Natural gas, which is lighter than air, tends to 
collect in high areas. LP gas is heavier than air 
and tends to settle in low areas.

 Model # 

Nat. Gas (*) 

LP Vapor (**)

   1/2 

Load  Full Load 

1/2 Load 

Full Load

 05207 

156 

220 

1.58/58 

2.40/88

Summary of Contents for ASPAX1CCA015













































Reviews: