background image

SECT

IO

N

6

6-21

T-268-07

4. If adjustment is required, loosen setscrew

(cross-recessed head). Using a 7 mm wrench, rotate

the adjustment screw clockwise to set the stylus 1 to
2

_

C (1.8 to 3.6

_

F) higher than desired temperature.

5. Rotate the adjustment screw counterclockwise to

set the stylus about 0.5

_

C (0.9

_

F) higher than set

temperature. Rotate the chart by hand. The

indicated temperature should be 0

_

C (32

_

F).

c. Replacing Sensor Probe

1. Remove box from unit.
2. Remove nut and bushing (item 9, Figure 6-20).

1

2

3

4

9

5

6

7

8

1. Voltage Indicator

2. Indicator Test Switch

3. Battery (“C” size, Alkaline)

4. Sensor Assembly

5. Stylus

6. Stylus Lifter

7. Setscrew (Adjustment)

8. Bulb and Mechanism

9. Bushing and Nut

Figure 6-20. Saginomiya Recording Thermometer

3. Install replacement probe and bushing. Seal with

silicone before securing to case.

4. Install box into unit.

NOTES

S

One full turn with the adjustment screw
changes the indicated temperature by

approximately 5

_

C (9

_

F).

S

Overtightening of setscrew may change set
temperature.

S

Calibration should only be done when bulb
temperature is decreasing.

S

DO NOT move stylus by hand.

6.21 MAINTENANCE OF PAINTED SURFACES

The refrigeration unit is protected by a special paint
system against the corrosive atmosphere in which it
normally operates. However, should the paint system be

damaged, the base metal can corrode. In order to protect
the refrigeration unit from the highly corrosive sea
atmosphere, or if the protective paint system is
scratched or damaged, clean area to bare metal using a
wire brush, emery paper or equivalent cleaning method.

Immediately following cleaning, spray or brush on
zinc-rich primer. After the primer has dried, spray or
brush on finish coat of paint to match original unit color.

6.22 POWER AUTOTRANSFORMER (OPTIONAL)

If the unit does not start, check the following:
a. Make sure the 460 vac (yellow) power cable is

plugged into the receptacle (item 3, Figure 2-9) and
locked in place.

b. Make sure that circuit breakers CB-1 and CB-2 are

in the “ON” position. If the circuit breakers do not
hold in, check voltage supply.

c. There is no internal protector for this particular

transformer design, therefore, no checking of the
internal protector is required.

d. Using a voltmeter, and with the primary supply

circuit ON, check the primary (input) voltage (460
vac). Next, check the secondary (output) voltage
(230 vac). The transformer is defective if voltage is
not available.

6.23 SENSOR CHECKOUT PROCEDURE (AMBS,

DTS, RRS, RTS, SRS & STS)

An accurate ohmmeter must be used to check the

resistance values shown in Table 6-1.
Due to the variations and inaccuracies in ohmmeters,
thermometers or other test equipment, a reading within

2% of the chart value would indicate a good sensor. If a
sensor is defective, the resistance reading will usually
be much higher or lower than the resistance values given
in Table 6-1.

6.23.1 Checking Sensor (RRS, RTS, SRS or STS)

a. Place the sensor (sensing bulb) in a 0

_

C (32

_

F)

ice-water bath. The ice-water bath is prepared by
filling an insulated container (of sufficient size to

Summary of Contents for 69NT40-511-1











































































































































Reviews: