![background image](http://html1.mh-extra.com/html/carrier/48fk034/48fk034_operating-and-troubleshooting-manual_2560984044.webp)
44
Table 20 — Compressor Loading and Unloading Sequences (cont)
TROUBLESHOOTING
By using the display module, actual operating conditions of
the unit are displayed while it is running. The Quick Test func-
tion allows proper operation of compressors, compressor un-
loaders, fans, and other components to be checked while unit is
stopped. If an operating fault is detected, an alarm is generated
and an alarm code(s) is displayed. For checking specific items,
see Table 21.
Checking Display Codes —
To view the digital dis-
play codes, press the button located to the right of the LED dis-
play/set point board in the control box. See Table 22 for Opera-
tional Status Codes. See Table 23 for Diagnostic Codes.
Complete Unit Stoppage —
If the unit is off, there are
several conditions that can cause this situation to occur:
•
Remote ON/OFF circuit in Unoccupied mode.
•
Unit ON/OFF switch moved to OFF position.
•
Programmed schedule at the timeclock.
•
General power failure.
•
Blown fuse in the control power feed.
•
Open control circuit fuse.
•
Operation of the unit blocked by the demand limit
function.
•
Unit supply-air temperature (T1) thermistor failure.
•
Supply-air fan is not operating.
•
High duct static pressure.
Single Circuit Stoppage —
If a single circuit stops,
there are several potential causes:
•
Open contacts in the compressor high-pressure switch.
•
Low refrigerant pressure.
•
Thermistor failure.
•
Unit supply-air temperature thermistor (T1) failure.
•
Compressor circuit breaker trip.
•
Operation of the circuit blocked by the demand limit
function.
Table 21 — Controls Troubleshooting
COOLING
STAGE
SIZE 088 UNITS
Lead Circuit
Lag Circuit
Active
Cylinders
Percent
Capacity
Comp 1
Unloader
U1
Unloader
U2
Comp 2
0
OFF
OFF
OFF
OFF
0
0
1
ON
ON
ON
OFF
2
16
2
ON
ON
OFF
OFF
4
33
3
ON
OFF
OFF
OFF
6
50
4
ON
ON
ON
ON
8
66
5
ON
ON
OFF
ON
10
83
6
ON
OFF
OFF
ON
12
100
COOLING
STAGE
SIZE 104 UNITS
Lead Circuit
Lag Circuit
Active
Cylinders
Percent
Capacity
Comp 1
Unloader
U1
Comp 3
Comp 2
Comp 4
0
OFF
OFF
OFF
OFF
OFF
0
0
1
ON
ON
OFF
OFF
OFF
4
20
2
ON
OFF
OFF
OFF
OFF
6
30
3
ON
ON
OFF
ON
OFF
10
50
4
ON
OFF
OFF
ON
OFF
12
60
5
ON
ON
OFF
ON
ON
14
70
6
ON
OFF
OFF
ON
ON
16
80
7
ON
ON
ON
ON
ON
18
90
8
ON
OFF
ON
ON
ON
20
100
SYMPTOM(S)
PROBABLE CAUSE(S)
SOLUTION(S)
Controls do not seem
to be operating.
Remote on-off function may be
keeping controls off.
Check status.
Evaporator fan does not run.
1. Circuit breaker open.
2. Inverter overload (if equipped).
1. Find cause and reset circuit breaker.
2. Find cause and reset.
Compressor does not run.
1. Circuit breaker is open.
2. There is no demand for cooling.
3. The control is locking out cooling operation.
4. Demand Limit in effect.
1. Find cause and reset circuit breaker.
2. Correct operation.
3. Check rotating display for alarm codes. Resolve
alarm cause and reset control by changing to
standby and back to run mode.
4. Check Demand Limit Settings.
Condenser fans do not
turn on.
Circuit breaker is open.
Find cause and reset circuit breaker
Cooling demand exists and
economizer modulates, but
compression is not operating.
Compression cannot be initiated
until economizer damper is 90% open.
Correct operation.
Summary of Contents for 48FK034
