8
Specifications subject to change without notice. OM-40MAQ-07
Timer Function
TIMER ON
(to start the unit) and
TIMER OFF
(to stop the unit) can
be used separately or together.
Timer ON Only
This function allows the unit to start automatically at the set time. The
TIMER ON
function can be set while the unit is on or off.
UNIT ON
1. Press
TIMER ON
to initiate the auto-on time sequence. The set
time is displayed in the remote control display. Every time
TIMER
ON
is pressed, the time increases by 30 minutes, up to 10h. It
increases by 60 minutes, afterwards, until the time setting reaches
24h. When the
TIMER ON
is set, the
TIMER
light on unit
illuminates. The unit continues to run at the set time.
UNIT OFF
1. Set the timer described in the
UNIT ON
section. The unit starts at the
set time.
2. Adjust the
TIMER ON
settings to 0.0 to cancel this option.
Timer OFF Only
This function allows the unit to stop automatically at the set time. The
timer can be set while the unit is on or while it is off.
UNIT ON
1. Press
TIMER OFF
to initiate the auto-off time sequence. The
set time appears on the remote control display. Every time
TIMER
OFF
is pressed, the time increases by 30 minutes, up to 10h. It
increases by 60 minutes, afterwards, until the time settings reach
24h. When the
TIMER OFF
is set, the timer light on the unit
illuminates and the unit turns off automatically at the set time.
UNIT OFF
1. Set the
TIMER
OFF
as described in the
UNIT ON
section. The
TIMER
display on the unit illuminates and the unit remains off.
2. Adjust the
TIMER ON
settings to 0.0 to cancel this option.
Timer ON and Timer OFF
Use both functions to program the unit to turn on and shut off at
specified times.
UNIT ON
1. Set
TIME OFF
as previously described.
2. Set
TIME ON
as previously described. The unit turns off
automatically at the set
TIME OFF
and turns on at the set
TIME
ON
.
UNIT OFF
1. Set
TIMER ON
as previously described.
2. Set
TIMER OFF
as previously described. The unit starts
automatically at the set
TIME ON
and turns off at the set
TIME
OFF
.
SLEEP Mode
SLEEP
mode is used to conserve energy and can be used when the
unit is in the
COOL
,
HEAT
or
AUTO
mode only.
Fig. 12 — Sleep Mode
COOLING Mode
1. Push
SLEEP
. After 1 hour the set point raises by 1.8°F (1°C). After
another hour, the set point raises by another 1.8°F (1°C) and the fan
runs in a low speed. The unit shuts off 5 hours after setting the
SLEEP
mode.
SLEEP
mode cancels if either
MODE
,
TEMP
,
FAN
,
TIMER
, or
ON/OFF
on the remote control is pressed.
HEATING Mode
Same as the
COOLING
mode however the set points are lowered by
1.8°F (1°C).
TURBO Mode
Use
TURBO
to cool or heat the room rapidly.
1. Press
TURBO
. An audible “beep” is heard if the indoor unit
supports this function. The fan runs on super high speed. The
TURBO
mode terminates automatically 20 minutes after selecting
TURBO
.
2. To cancel
TURBO
, select
TURBO
mode again. When the
TURBO
mode terminates, the unit reverts to the original setting.
SELF CLEAN Mode
1. Press
CLEAN
to activate or deactivate the self-cleaning function.
Under this function, the air conditioner automatically cleans and
dries the evaporator. The cleaning cycle takes 30 minutes, after
which the unit turns off automatically. The unit operates in the
following sequence:
•
FAN ONLY mode at LOW fan speed
•
HEATING
operation with
LOW
fan speed
•
FAN ONLY
operation
•Stop Operation
•Turn off
2. To cancel the
CLEAN
mode, press
CLEAN
. The operation ends
and the unit turns off. This function can be activated only in the
COOL
or
DRY
modes. Before selecting this function, it is
recommended to run the air conditioner under
COOLING
operation for about half an hour. Once the
SELF CLEAN
function
is activated, all timer settings will cancel.The indoor unit displays
SC.
NOTE:
The
SELF CLEAN
mode is available
ONLY
on the single
zone models.
TIMER
ON
TIMER
OFF
Set
temperature
1hr
1hr
7 hours
timer off
+/- 1 C/2 F
SLEEP Operation
+/- 1 C/2 F
Saving energy during sleep
TIMER
ON
ON/OF F
ON/OF F
TIMER
OFF
ON/OF F
ON/OF F
TIMER
ON
TIMER
OFF
ON/OF F
ON/OF F
SLEEP
TURBO
CLEAN
