background image

OM-40MAQ-07                                                                            Specifications subject to change without notice.                                                                                         

11

Cleaning the Indoor Unit Front Panel

To clean the front panel on the indoor unit, wipe the outside with a 
soft, dry cloth.

Pre-Season Inspection

After long periods of non-use, or before periods of frequent use, 
perform the following steps:

Fig. 19 — Pre-Season Inspection

Preparing for Extended Shutdown Period

Clean the filters and reposition them in the unit. Operate the unit in 

FAN ONLY

 mode for 12 hours to dry all internal parts. Turn main 

power supply off and remove batteries from the remote control.

Fig. 20 — Extended Shutdown Period Steps

System Operation Recommendations

The items outlined in the following list help to assure proper system 
operation:

• Replace both remote control batteries at the same time.

• Point the remote control toward the unit display panel when 

transmitting a command.

• Keep doors and windows closed while unit is operating.

• Contact an authorized service representative if a problem 

arises that cannot be easily resolved.

• Do not perform cleaning or maintenance activities while the 

unit is on.

• Keep the display panel on the unit away from direct sunlight 

and heat as this may interfere with remote control 
transmissions.

• Do not block air intakes and outlets on the indoor or outdoor 

units.

Energy Saving Recommendations

The following recommendations will add greater efficiency to the 

ductless system:

• Select a comfortable thermostat setting and leave it at chosen 

setting. Avoid continually raising and lowering the setting.

• Keep the filter clean. Frequent cleaning may be necessary 

depending on indoor air quality.

• Use drapes, curtains or shades to keep direct sunlight from 

heating the room on very hot days.

• Limit the unit’s run time by using the TIMER function.

• Do not obstruct the air intake on the front panel.

• Turn on the air conditioning unit before the indoor air 

becomes too uncomfortable.

Clean all filters

Turn on FAN function until

unit dries out completely

Turn off the unit and

disconnect the power

Remove batteries

from remote control

Summary of Contents for 40MAQ













Reviews: