background image

GB - 10

38GL...G / 38GLS...G / 38YY...G / 38YYS...G 

R-410A

Electrical connections

Notes:

1. Unit is suitable for outdoor installation.
2. 
Data referred to the outdoor unit only.
3. Starting current duration is usually lower than 1 sec.
4. Wire size shown applies to line length up to 15 m.
5. If the indoor unit is provided with an electric heater, consult indoor unit installation manual for correct sizing of the wires.
6. The mains supply connecting cable must be H07 RN-F type (or higher), synthetic rubber insulation with Neoprene coating, according to

EN 60335-2-40 codes.

• Make refrigerant connections before electrical

connections.
When disassembling, disconnect electrical connections before
refrigerant connections.

IMPORTANT:
Make ground connection prior to any other electrical
connections.

• Remove electric box cover.

• Make electrical connections between units prior to proceeding

to mains supply unit connection.

• Connect the wires to the terminals according to the wiring

diagram and firmly tighten.

• Before proceeding with the unit connection to the mains supply

locate live L and neutral N, then make connections as shown
in the wiring diagram.

•  Ensure that mains supply connection is made through a

switch that disconnects all poles, with contact gap of a least 3
mm.

• The mains supply connecting cable must be H07 RN-F type

(or higher), synthetic rubber insulation with neoprene coating,
according to EN 60335-2-40.

Note:
All field electrical connections are the responsibility of the
installer.

Refer to the indoor unit installation manual for sizing the
connection wires between units.

Note:
After connections have been completed, replace electric box
cover.

Table IV: Electrical data

Unit

A

A

W

A

W

A

W

A

W

A

mm

2

38GL(S)018G

40

9,3

2110

13,1

2560

20

2,5

38GL(S)024G

60

10,1

2300

15,5

3100

25

2,5

38GL-028G

70

13,9

3030

18,9

3600

16

4

38GL-036G

76

14,9

3250

19,4

3700

16

4

38GL-048G

114

15,8

3450

28,2

5350

16

6

38YY(S)018G

40

8,8

1980

12,4

2430

8,9

2015

11,8

2300

20

2,5

38YY(S)024G

60

11,4

2465

14,9

2890

12,2

2675

14,3

2775

25

2,5

38YY-028G

70

13,4

2940

19,5

3800

14,1

2680

16,9

3890

30

4

38YY-036G

76

15,7

3430

19,9

4020

15,9

3030

20,0

3960

32

4

38YY-048G

114

17,7

3860

28,7

5450

17,5

3320

25,7

4900

40

6

Starting

current

(3)

Heating

Cooling

Power input 

(2)

Main power

connections 

(6)

Time-delay

fuse

gL type

Wire size

(4-5)

Nominal conditions

230V  ~  50Hz

ISO 5151.2/T1

indoor 27

°

C d.b.  19

°

C w.b.

outdoor 35

°

C d.b.  24

°

C w.b.

Peak conditions

198V  ~  50Hz

ISO 5151.2/T1

indoor 32

°

C d.b.  23

°

C w.b.

outdoor 43

°

C d.b.  32

°

C w.b.

Nominal conditions

230V  ~  50Hz

ISO 5151.2/High+

indoor 20

°

C d.b.  15

°

C w.b.

outdoor 7

°

C d.b.   6

°

C w.b.

Peak conditions

198V  ~  50Hz

ISO 5151.2/High+

indoor 27

°

C

outdoor 24

°

C d.b.  18

°

C w.b.

Summary of Contents for 38GL...G















Reviews: