background image

2

Piping Connections

 — 

Attach water supply and return

lines  to  connections  indicated  on  condensing  unit  (Fig.  2).

Water leaving condenser should not be connected directly into

sewer lines; check local codes.

Attach  refrigerant  liquid  and  suction  lines  to  condensing

unit (Fig. 2); suction and  discharge lines to  compressor unit

(Fig.  3  and  4).  Discharge  line  muffler  and  check  valve  are

factory supplied with 06E compressor units. Install the muffler

as close to shutoff valve as possible and install the check valve

in the discharge line close to the muffler, on the downstream

side. When soldering or brazing piping to valves, disassemble

the valve or wrap it in wet cloth to prevent damage by heat.

Allow flexibility in suction line so compressor suction valve

may be moved aside for access to suction strainer.

A solenoid valve is necessary for single pumpout control

used on 06E and 07E units. Install the valve (field supplied) in

the  liquid  line,  just  before  expansion  valve. A  filter  drier  of

adequate size should be installed in liquid line between con

-

denser and solenoid valve.

Pressure relief valve located on top of condenser will open

to  relieve excessive  pressure,  allowing  refrigerant  to escape.

Most local codes require piping from valve to outdoors.

Refer to Carrier System Design Manual for standard piping

techniques.

Electrical Connections

UNBALANCED 3-PHASE SUPPLY VOLTAGE — 

Never

operate a motor where a phase imbalance in supply voltage

is greater than 2%. 

Use the following formula to determine

the % voltage imbalance:

% Voltage Imbalance =

Example: Supply voltage is 240-3-60

AB = 243 volts

BC = 236 volts

AC = 238 volts

Determine maximum deviation from average voltage:

(AB) 243 – 239 = 4 volts

(BC) 239 – 236 = 3 volts

(AC) 239 – 238 = 1 volt

Maximum  deviation  is  4  volts.  Determine  %  voltage

imbalance:

This amount of phase imbalance is satisfactory as it is below

the maximum allowable 2%.

POWER SUPPLY — Field  wiring  must  comply  with  local

and national codes. See Table 1.

Install a branch circuit fused disconnect of adequate size to

handle starting  current. The  disconnect  must be within sight

from  the  unit  and  readily  accessible,  in  compliance  with

National Electrical Code (NEC), Section 440-14.

Line power is brought into control center through indicated

opening. Connect  line power  supply to terminal block TB1;

connect  power  leads  to  terminals  L1,  L2  and  L3.  Connect

control circuit power supply (115 volts) to terminals 1 and 15

on terminal block TB2. Refer to Fig. 5.

Wiring connections for field-supplied equipment are shown

on wiring diagram. See Fig. 6.

ACCESSORIES — Field-installed  accessories  for  the  06E

and  07E  units  are  control  circuit  transformer  and  gage

panel (3  gages). Refer to accessory literature for  installation

instructions.

100 x max voltage deviation from avg voltage

average voltage

A B C

MOTOR

Average Voltage = 243 + 236 + 238

3

 = 717

3

= 239 volts

% Voltage Imbalance = 100 x 4 = 1.7%

239

IMPORTANT:  If  the  supply  voltage  phase  imbalance  is

more than 2%, contact your local electric utility company

immediately. Allowing the unit to operate with a voltage

imbalance in excess of 2% may void the warranty.

Summary of Contents for 05FY/HY Series





















Reviews: