9
Carrera DIGITAL 124/132
EVOLUTION
Please note that Evolution (analog system) and Carrera
DIGITAL 124/132 (digital system) involve two separate and com-
pletely independent systems. We hereby expressly indicate that
both systems must be kept separate when setting up the track, i.e.
no connecting rail from Evolution may be used together with the con-
necting rail and Black Box of the Carrera DIGITAL 124/132, even if only
one of the two connecting rails (Evolution connecting rail or Carrera
DIGITAL 124/132 connecting rail and Black Box) is attached to the
current supply. Furthermore, no other Carrera DIGITAL 124/132
components (switches, electronic lap counter, pit stop) may be built
into an Evolution course, i.e. via analog operation.
Non-compliance with the above information may result in damage or
destruction of the respective Carrera DIGITAL 124/132 components.
In this case no warranty may be claimed.
Troubleshooting
Driving tips
Troubleshooting:
In case of any malfunctions, please check the following:
• Has the connection to the power supply been established correctly?
• Have transformer and speed controllers been connected correctly?
• Are the track connections faultless?
• Are the racetrack and track slots clean and free of any foreign
objects?
• Are the sliding contacts in order and do they make contact with
the track slot?
• Are the cars correctly coded to the according speed controller?
• The track‘s current feed will be switched off automatically for 5
seconds, if there is an electrical short circuit: This will be notified by
audible and visual signals.
• Are the cars placed on the track in running direction? In case of non-
functioning push the running direction switch which is on the car´s bottom.
Note:
During operation small car parts as spoilers or mirrors may get off or
brake due to being original detailed parts of the car model. To avoid
this it is possible to remove them before operation.
Driving technique:
• You can drive fast along the straight track but you should brake before
the curve and then accelerate again when coming out of the curve.
• Do not fasten or block the vehicles when the motor is running:
overheating or damage to the motor could result otherwise.
Note:
When using track systems which are not manufactured by Carrera
the existing guide keel has to be replaced by the special guide keel
(#20085309). While using the Carrera crossing (#20020587) or high
banked curve 1/30° (#20020574) slight driving noise might occur
which is due to the full-scale genuineness and does not affect flaw-
less operation.
All Carrera spare parts are available in the webshop:
carrera-toys.com
Delivery exclusively to Germany, Austria, Netherlands, Belgium and
Luxembourg.
Technical specifications
Output voltage: Toy transformer
18 V
54 VA (Carrera DIGITAL 124)
14,8 V
51,8 VA (Carrera DIGITAL 132)
Electricity modes:
1.) Operating mode = cars are operated via speed controllers
2.) Idle mode = speed controllers not activated, no game
3.) Stand-by mode = after approx. 20 minutes idle mode the
connecting section switches to stand-by mode. LED flashes at
long intervals.
CURRENT CONSUMPTION < 1 watt / 1w
To reactivate the controller, switch it off for 2 or 3 seconds, then
switch it on again.The racetrack is then once again in standby mode.
4.) Off-state = power supply unit disconnected from mains supply
This device is marked by “selective sort throught” symbol related to
sort through domestic, electric and electronic, waste. This means
the product must be treated by a specialized “sorting/collecting” sys-
tem in accordance with European directive 2012/19/CE, to reduce
the impact upon environment. For more precise information, please
contact your local administration. Electronical product which are
not going through special collecting, are potentially dangerous for
environment and human health, because of dangerous substance.
Output voltage: Toy transformer
18 V
54 VA (Carrera DIGITAL 124)
14,8 V
51,8 VA (Carrera DIGITAL 132)
Electricity modes:
1.) Operating mode = cars are operated via speed controllers
2.) Idle mode = speed controllers not activated, no game
3.) Stand-by mode = after approx. 20 minutes idle mode the
connecting section switches to stand-by mode. LED flashes at
long intervals.
CURRENT CONSUMPTION < 1 watt / 1w
To reactivate the controller, switch it off for 2 or 3 seconds, then
switch it on again.The racetrack is then once again in standby mode.
4.) Off-state = power supply unit disconnected from mains supply
