CarpMadness Phantom 2020 Assemble Instructions Download Page 4 | Manualshive

Page: 4 / 21

background image

Finally, the steering and return unit has to be installed on the outside of the jet. This was

already pre-assembled by us.

First, the 2 Bowden cables must be glued into the receptacle, greased well and then

screwed onto the steering and return unit.

«
...
2
3
4
5
6
...
»

Summary of Contents for Phantom 2020






















Reviews:

No comments

Related manuals for Phantom 2020

Brand: 3d Pages: 17

Brand: Outcast Pages: 7

Brand: Hobie Pages: 27

Brand: Hobie Pages: 27

KAYAK-BW-01-PK-iKAYAK-RED

Brand: Bluewave Pages: 6

Grand Banks 49 Classic

Brand: Dream Catcher Pages: 71

Riva Rivale - Vantage

Brand: Allied Marine Pages: 16

CORSIVA 500 TENDER

Brand: Corsiva Yachting Pages: 38

Brand: Lifetime Pages: 16

GP1200R WaveRunner 2001

Brand: Yamaha Pages: 245

Brand: SEABOB Pages: 4

Brand: FitNord Pages: 84

Brand: Arey's Pond Pages: 10

303 Single Seater

Brand: Access Dinghy Sailing Pages: 4

Brand: Bestway Pages: 6

Brand: AB Inflatables Pages: 46

Brand: Sea Eagle Pages: 12

Brand: Sea Eagle Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands