Carpenter MFG. Co., Inc. Compu-Strip 93 Operator'S Manual Download Page 18

Page: 18 / 49

CARPENTER MODEL 93 COMPU-STRIP

Phone: 315-682-9176 Fax: 315-682-9160

Page

Revised 08/23/13 Website: www.carpentermfg.com E-mail: [email protected]

CARPENTER MODEL 93 COMPU-STRIP

PROGRAMMING

SHORT MODE

The Model 93 has the capability of processing wire with stripping specifications of two inches or less of insulation left
between the stripped ends. The LCD display will read

SHORT

when the short wire mode is activated based upon the

stripping parameters you have entered.

LCD DISPLAY PROMPT

ACTION REQUIRED

CARPENTER MFG.

Press

ENTER.

MODEL 93 COMPU STRIP

VERSION

PLEASE PRESS ENTER

Press

TRAILING STRIP

key. This value is the length of insulation to be stripped from

the left end (trailing end) of wire.

0.00

Enter dimension. Press

ENTER.

PLEASE

ENTER

TRAIL STRIP LENGTH

PLEASE

ENTER

Machine will default to “1”. Press

ENTER.

When operating machine in SHORT MODE

NUMBER OF PULL STEPS

only one pull step is allowed due to the short processing lengths.

STEPS = 1

Press

WIRE LENGTH

key. This value is the overall length of pieces being processed.

0.00

Enter dimension. Press

ENTER.

PLEASE ENTER
OVERALL WIRE LENGTH

Press

LEADING STRIP

key. This value is the length of insulation to be stripped from

the right end (leading end) of the wire.

0.00

Enter dimension. Press

ENTER.

PLEASE

ENTER

LEAD STRIP LENGTH

PLEASE

ENTER

Machine will default to “1”. Press

ENTER.

When operating machine in SHORT MODE

NUMBER OF PULL STEPS

only one pull step is allowed due to the short processing lengths.

STEPS = 1

TRAILING

STRIP

WIRE

LENGTH

LEADING

STRIP

Summary of Contents for Compu-Strip 93


















































Search results

Summary of Contents for Compu-Strip 93

Reviews:

Related manuals for Compu-Strip 93

Brands by name

Popular brands

Carpenter MFG. Co., Inc. Compu-Strip 93, Operator'S Manual

Search results

Summary of Contents for Compu-Strip 93

Reviews:

Related manuals for Compu-Strip 93

Brands by name

Popular brands