background image

Carmanah M850 & M860 Self-Contained LED Lantern Instructions 

v1.

1

 

Jan

 201

6

 

Setting the Lantern Flash Characteristic 

Note:  The lanterns are shipped from the factory set to default flash characteristic FL 4 (0.4) 
(code 174).  The flash rhythm can easily be changed to a different setting using the following 
procedure: 

Step

Action 

1

 

Wake the lantern by repeatedly pressing the 

Power Key

 

 until 

you get a single flash.  The lantern must be in the 

on

 mode to 

program.  After the flash, you have 60 seconds to make another key 
entry.  If you are entering all programming codes within 60 seconds 
of each other, you do not need to press the Power Key each time. 

2

 

Press the 

A Key

 

 (for Flash Character Menu). 

3

 

Press the 

Set Key 

 

to unlock the flash characteristic setting. 

4

 

Rhythm

Code

Q   (0.3s flash, 0.7s eclipse) 

129 

FL 2.5 (0.3)   (0.3s fl, 2.2s ec) 

049 

FL 4 (0.4)   (0.4s fl, 3.6s ec) 

174 

FL 5 (0.5)   (0.5s fl, 4.5s ec) 

069 

FL 6 (0.6)   (0.6s fl, 5.4s ec) 

073 

FL (2) 5   (0.4s fl, 0.6s ec, 0.4s fl, 3.6s ec) 

175 

FL (2+1) 6   (0.3s fl, 0.4s ec, 0.3s fl, 1.2s ec, 

0.3s fl, 3.5s ec) 

022 

Iso 6   (3.0s fl, 3.0s ec) 

081 

Mo (A)   (0.4s fl, 0.6s ec, 2.0s fl, 5.0s ec) 

176 

Occ 4   (3.0s fl, 1.0s ec) 

118 

Enter the selected 

three digit code

 for the characteristic with the 

numeric key pad.  The codes are same for all Carmanah lanterns. 

The digital LED display will show the codes as you are entering 
them, and the lantern will provide a single flash for each successful 
key entry. 

5

 

Press the 

Set Key 

 again to lock the characteristic setting.   The 

lantern will provide three quick flashes to confirm that the new 
setting has been accepted and locked.  If incorrect, the display will 
show “

Err

.”  

Important

: Anytime the flash code is changed, the 

lantern will determine if the new flash characteristic can support 
the preprogrammed effective intensity and 

will 

automatically lower 

it if necessary.  Always review the programmed effective intensity 
setting after changing the flash code to ensure it’s still as desired. 

All manuals and user guides at all-guides.com

Summary of Contents for M850



































Reviews: