Carlton SP5014TRX, Owner'S Manual

Page: 24 / 160

SP5014TRX MACHINE SPECIFICATIONS
4
General:
Weight: 2215 Pounds
Length: 84 Inches
Height: 56 Inches
Width: 34
Inches
Track type: Rubber track
Track Foot Print: 7”
Track Ground Pressure:
4 PSI
Track Length: 42-1/2”
Controls:Side Mounted – Optional Remote
Fuel Capacity:
10.3 Gallons
Battery: 650 Cold Cranking Amps
Curb Clearance: 13 Inches
Cutter Wheel Diameter:
21 Inches with Teeth
Cutter Wheel Thickness:
1 ¼ Inch - Blanchard Ground
Cutter Wheel RPM:1350 Nominal
Engine:
Manufacturer:
Vanguard Series 540000 V-Twin Engine
Number of Cylinders: Two
Bore Type: Cast Iron Sleeve
Valves: Overhead
Bore:
3.4 Inches (85.5 mm)
Stroke: 3.4 Inches (86.5 mm)
Displacement: 60
Cubic Inches (993 cc)
Compression Ratio: 8.25:1
Maximum RPM: 3600
Horsepower: 35
Peak Torque: 52 Ft*Lbs @ 2,400 RPM
Weight: 125 Lbs (56.8 KG)
Oil Capacity w/Filter: 77.8 oz
Cooling Medium: Air
Air Cleaner: Dry Type Canister with Safety Element
Oil Filter: Spin On
Lubrication: Full Pressure w/Full Flow Filter
Electrical: 12 Volt
Hydraulic System:
Hyd Pump
Displacement: .267 cu in (4.3 cc)
Hyd Pump Drive
System: Direct Drive Coupling
Flow: 4.09 GPM
System Relief: 1850 PSI
Oil Tank Capacity: 3.6 Gallon
Oil Type: AW 46
Valve: Series Type with Fine Metering
Check Valves:Cartridge Counterbalence
Valve in Lift, Swing, and Drive Circuits
Hose:Steel Braided 16,000 PSI Burst - Exceeds
SAE 100R2
Oil Filter: 10 Micron Full Flow
Lift Cylinder:3" X 12" with 1 3/8" Rod and
Replaceable End with Captured Pins
Drive System:
Engine Sheave: 6/3V5.3
Jackshaft Sheave: 6/3V14.0
Drive Belt: 6/3V710
Jackshaft Sprocket: 8M-40S-62 Gates PolyChain
Cutter Head Sprocket: 8M-40S-62 Gates PolyChain
Drive Belt: 8M-1200-62 Gates PolyChain
Jackshaft : 1 11/16 Inch
Cutter Head Shaft: 1 11/16 Inch
Engine Engagement: Sliding Engine Carriage
Belt and Chain Shields: Metal Bolt On
Bearings:
Jackshaft Bearings: 1 11/16 Inch Tapered Roller
Bearings
Cutter Head Bearings: 1 11/16 Inch Tapered Roller
Bearings
Swing Bearings: Adjustable Tapered Roller
Bearings
Frame:
Tongue: 3" X 3" X 3/8" wall Mechanical Tubing
Boom: 4 1/2" X 4 1/2" X 1/4" wall Mechanical
Tubing
Boom Box: 1/4" Plate
Pivot Plate: 1/2"
Supports: Gussets used Throughout
Cutter Wheel:
Wheel Diameter: 21 Inches with Teeth
Wheel Thickness: 1 ¼ Inch
Wheel Speed: 1350 RPM Nominal
Number of Teeth: 32 Carbide Tipped Sandvik
Wheel Type: Razor
Chip Guards: Rubber and Metal
Cutting Dimensions:
Below Ground: 14 Inches
Above Ground: 34 Inches
Width of Cut: 50 Inch Arc