#34481-BHFFCa
The Remote Controlled Ceiling Alarm is
designed to be mounted on the ceiling in
the center of a room at a height of 8 to 10
feet from the ground, where the PIR
(passive infra-red ) sensor will detect the
movement of heat over an area of 20 feet
by 360 degrees. It is armed/disarmed
with the infra-red remote control
keychain.
25701 Science Park Drive
Cleveland, Ohio 44122
www.lamson-sessions.com
Made in China
© 2004
0407 SR4900D
•
Powerful 110dB alarm or 90dB chime.
•
Automatic reset after activation.
•
Low battery indicator.
•
Entry and exit delays.
•
Power supply: 3 “C” alkaline batteries (not included) or AC adapter option.
•
Includes one remote control unit (two 1.5-volt batteries installed). Additional
units available for family members, sold separately.
ARMING/DISARMING THE ALARM
The unit is armed/disarmed by use of the
infra-red remote control keychain, which
operates up to a distance of 25 feet from
the alarm. Simply point the remote control
at the alarm, press once and release.
1.
The unit will sound “Ding-Dong” to
signify entry into Chime mode. In this
mode, whenever motion is detected, a
“Ding-Dong” sound will play.
2.
When the Remote Control is pressed a
second time, the unit will give one
“beep” signifying entry into Alarm
mode. The Green LED will light up for
approx. 30-45 seconds allowing exit
from the detection zone.
To disarm the unit, simply press the
remote control a third time. The unit will
give two beeps signifying the unit being
disarmed. When entering the detection
zone, approximately 10 seconds are given
to deactivate the unit before the alarm
sounds.
If the green light is flashing upon your
return, there has been an intrusion. The
alarm has been set off, and has reset itself.
THE ALARM
The alarm is activated by the motion
detection sensor. After a 10 second delay,
the 110dB high frequency alarm will
automatically sound once the sensor has
detected movement. It will remain on for
approximately one minute if no further
movement is detected, after which it
automatically shuts off and resets itself.
LOW BATTERY INDICATOR
When the batteries are running low, the
red LED on the front of the unit will flash.
The alarm will also beep every 20 seconds
as a warning that the batteries need to be
replaced.
BATTERY BACK-UP FUNCTION
If there is a power failure when the unit is
being operated by the AC power source,
as long as the unit contains the correct
batteries, it will automatically switch to
battery power leaving the unit armed and
ready to detect motion.
KEYCHAIN BATTERY REPLACEMENT
Batteries are located within the main
alarm compartment. Simply remove the
screw on the back of the remote control
keychain at the bottom. Replace batteries
with 2 button cell batteries (1.5v).
IMPORTANT
The Remote Controlled Ceiling Alarm is a
sensitive electrical product and the
following precautions should be followed:
Do not drop the unit.
Do not place the unit close to a source
of direct heat.
Do not use different types of batteries
or mix old and new ones.
Do not use rechargeable batteries.
As with most motion detection
devices, pets may activate your unit.
Not recommended for wall mounting.
LIMITED WARRANTY
The product you have purchased is guaranteed against defects in workmanship and
materials for the period stated on the package. Warranties implied by law are subject to the
same time period limitation. Some states do not allow limitations on how long an implied
warranty lasts, so this time limitation may not apply to you.
If the product fails due to a manufacturing defect during normal use, return the product and
dated sales receipt to the store where purchased for replacement OR send the product and
the dated sales receipt to:
Lamson & Sessions
25701 Science Park Drive
Cleveland, OH 44122 USA
Attn: LHP Customer Service
Not Covered - Batteries, light bulbs, and other expendable items are not covered by this
warranty.
Repair service, adjustment and calibration due to misuse, abuse or negligence are
not covered by this warranty. Unauthorized service or modification of the product or of any
furnished components will void this warranty in its entirety. This warranty does not include
reimbursement for inconvenience, installation, set-up time, loss of use, postage,
unauthorized service, or other products used in conjunction with, but are not supplied by,
Lamson & Sessions.
All requests for replacement must include a dated sales receipt (copies accepted). LAMSON
& SESSIONS IS NOT LIABLE FOR LOST PROFITS, INDIRECT, SPECIAL, EXEMPLARY,
INCIDENTAL OR CONSEQUENTIAL DAMAGES INCLUDING WITHOUT LIMITATION
ANY SUCH DAMAGES DUE TO IMPROPER WIRING OR MISUSE OF THE PRODUCT.
As
some states do not allow the exclusion or limitation of incidental or consequential damages,
the above limitation and exclusion may not apply to you.
This device complies with Part 15 of the FCC rules. Operation is subject to the following
two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause
undesired operation.
This device complies with RSS-210 of Industry Canada.
ALSO AVAILABLE FROM CARLON:
• Extend-A-Chime® – lets you hear your existing wired doorbell in remote areas of your
home or yard
• Plug-in and Battery Doorbells and Chimes
• On/Off Remote Switches
• Touch and Automatic Lighting Controls
This warranty gives you specific legal rights, and you may also have other rights which vary
from state to state. If you have questions or need further assistance, please call Lamson &
Sessions at: 1-800-346-2646, Mon. - Fri., 9 a.m. - 4 p.m. EST.
C
EILING
A
LARM
R
EMOTE
C
ONTROL
/W
IRELESS
TOOLS NEEDED
•
Phillips screwdriver
INSTALLATION
Insert 3 “C” size alkaline batteries (not
included) into the compartments on the
back of the unit, as indicated by the
internal markings. Alternatively, a 7.5-15
volt adaptor (not included) can be
connected to the AC jack socket which
can be found at the back of the unit.
Remove the protective film between green
and red LED lights.
Affix the mounting bracket to the ceiling
in the desired center position, using the
screws provided. The alarm can now be
attached to the bracket by aligning the
plastic clips to the bracket and turning
the unit clockwise. The clips will then
snap into the bracket. To take the unit off,
simply push the unit up against the
ceiling and rotate counter clockwise.
Motion Detector
Infra-Red Remote
Control Keychain
Green LED Light
(Operation Indicator)
Red LED Light (Low
Battery Indicator)
AC Jack
Mounting
Bracket
Battery
Compartment
