background image

CARLO GAVAZZI

Press and hold

and use the 

▲ 

or 

▼ 

buttons to select from the choices 

RlySSd 

or

AnLG

depending on the model supplied. SP2 and SP3 outputs will be automatically

allocated. (See output options table on page 8).

4

To enter initial configuration into controller memory

Press and hold

both 

▲ 

and 

▼ 

buttons for 3 seconds. The display will now read 

PArK

and measured variable (e.g. ambient temperature 23°). 

PArK

is displayed because a

setpoint has not yet been entered.

To display setpoint units

Press and hold 

The displays will now read 

unit 

(eg. 

°C

) and 

0

To enter setpoint
Press and hold

and use 

▲ 

button to increase or 

▼ 

button to decrease the reading and

scroll to required setpoint value. (The digit roll-over rate increases with time).

THE CONTROLLER IS NOW OPERATIONAL

WITH THE FOLLOWING FACTORY SETTINGS

P

roportional band/Gain

10ºC/18ºF/100 units

I

ntegral time/Reset

5 mins

D

erivative time/Rate

25 secs

Proportional cycle-time

20 secs 

(Typical setting for relay output)
DAC Derivative approach control

1.5

(Average setting for minimum overshoot)

Note:

For more precise control or for non temperature applications where a 

Linear input

transducer is being used, the controller may need to be tuned to the process.
Please refer to the following section on AUTOTUNE.

AUTOTUNE

This is a single shot procedure to match the controller to the process. Select either 

Tune

or

Tune at Setpoint

from the criteria given below.

The 

Tune

program should be used for applications other than those listed under 

Tune at

Setpoint

below. The procedure will apply disturbances when the temperature or process

reaches 75% of the setpoint value, causing overshoot which is monitored in order to adjust
the 

DAC

overshoot inhibit feature. Care should be taken to ensure that any overshoot is safe

for the process.

The 

Tune at Setpoint

program is recommended when:

The process is already at setpoint and control is poor

The setpoint is less than 100°C in a temperature application

Re-tuning after a large setpoint change

Tuning multi-zone and/or heat-cool applications.

Notes

DAC

is not re-adjusted by Tune at setpoint. 

Proportional Cycle Time

can be pre-

selected before running the Autotune program. (see page 5).

GETTING STARTED

After power-up the controller requires programming with the following information:

Type of Sensor

(See list of sensors p.22)

Operating unit

°C °F bAr PSi Ph rh SEt

Allocation of Output Device to SP1/SP2

(Relay / SSd) or analog. SP3 is always relay.

Setpoint

When the above information has been programmed into the controller it will be
operational with factory PID settings.

INITIAL SET-UP

On power-up the controller will display the self test sequence followed by the initial
display 

inPt : nonE

1

Select input sensor.

Press and hold

and use the 

or 

buttons to scroll through the sensor selection

list until the correct sensor is displayed. Release the buttons. The display will now read
selected sensor type e.g.

inPt : tCS 

(type S thermocouple).

Press

once

The display will now read

unit : nonE

LINEAR INPUT

When 

Linear Input

is selected, the display resolution of the 

setpoint

and many other

functions will be changed from the setting previously made at 

di.SP

in Level 2, to that set

at 

dECP

in Level A. 

It is therefore recommended that on completion of the 

Initial Set-up

the 

Linear Input

settings in Level A be completed before moving on to configure Levels 1, 2 and 3. (see
Set-up Procedure page 6).

2

Select operating unit.

Press and hold

and use the 

or 

▼ 

buttons to scroll through the unit selection list

until the correct unit is displayed. Release the buttons. The display will read selected
unit e.g. 

unit : °C

Press

once

The display will now read

SP1.d : nonE

3

Select SP1 (Main setpoint output device)

Analog output

The allocation of the analog output to 

SP1

automatically overrides the default

proportional cycle time

setting of 20 seconds. Where the analog output is allocated

to

SP2

, the default 

CyC.2

setting 

on/off

must be manually changed in  

Level 1

to a

time proportioning

setting to enable the analog output to operate in 

proportional

control mode

.

4

Summary of Contents for T2000P Series

























Reviews: