background image

EN

77-2709-R13  (10/2020)

3 / 8

www.carlisleft.com

Do not handle or use until safety precautions 
concerning Methyl Ethyl Ketone Peroxides in 
the Manufacturer’s literature have been read 
and understood.

Contact with foreign materials, especially 
strong mineral acids, metals (including certain 
equipment and containers) or metal salts, or 
exposure to heat above 135° F (57° C) may 
lead to violent decomposition, releasing 
flammable vapors which may self-ignite.

Do not get into eyes or on skin or clothing. 
Wear eye and skin protection when handling. 
Avoid breathing mist. Use with adequate 
ventilation. Store only it in the original  
closed container. Wash hands thoroughly  
after handling. Protect from direct sunlight, 
heat, sparks and other sources of ignition. 
Prevent contamination with foreign materials. 
Do not add to hot materials.

To maintain the chemical activity store below 

100° F (38° C).

In case of fire, use water spray, foam or dry 
chemical. 

In case of spill or leak, absorb or blend with 
inert, non-combustible material. Put in suitable 
container. Dispose of immediately in 
accordance with federal, state and local 
regulations.

Do not reuse container as some of the original 
hazardous contents may still be present. 

Follow the above precautions in handling. 

  WARNING

!

When using Binks equipment with  

Methyl Ethyl Ketone Peroxide in Plasticizer 

OBSERVE the following precautions

CORROSIVE TO THE EYES – MAY CAUSE BLINDNESS. 

MAY BE FATAL IF SWALLOWED. STRONG IRRITANT. 

CONTAMINATION OR HEAT MAY LEAD TO FIRE OR 

EXPLOSIVE DECOMPOSITION. COMBUSTIBLE.

FIRST AID

EYES 
Wash immediately (seconds count) with 
water and continue washing for at least 
15 minutes. Obtain medical attention.

SKIN 
Wash with soap and water. Remove 
contaminated clothes and shoes and again 
wash thoroughly with soap and water.

SWALLOWING 
Administer large quantities of milk or 
water. Obtain immediate medical attention 
for lavage.

Summary of Contents for Binks 7N









Reviews: