Carlin 601GAS Instruction Manual Download Page 6

Model 601GAS burner — Instruction manual

MN601GAS  012516

– 6 –

Where appliance instructions differ from this manual, follow the appliance instructions.

1.  Prepare site   •   prepare burner   •   mount burner

Vent system

Inspect, repair and/or replace vent system

  Do not install this burner unless you have verified the entire 

vent system and the appliance are in good condition and 

comply with all applicable codes. And . . .

 

The vent and chimney must be sized and constructed in 

accordance with all applicable codes. If intended for use 

with an oil burner as well, the vent system must comply 

with relevant codes for both gas and oil firing.

 

The vent system must not be pressurized unless the vent 

piping and vent system are designed accordingly. The vent 

must provide draft at all times (negative pressure in vent).

 

Do not install or use an existing manual damper in the vent 

connector or vent.

 

Do not connect the appliance vent connector to a chimney 

or vent serving a fireplace, incinerator or solid-fuel-burning 

apparatus.

 

In a cold climate, do not vent into a masonry chimney 

that has one or more sides exposed to the outside. 

Install a listed stainless steel liner to vent the flue 

products.

 

A defective vent system could result in severe personal 

injury, death or substantial property damage.

Vent/chimney sizing

•  Follow all local codes when sizing the vent and chimney

.

•  Refer to the appliance manufacturer’s manual, when available, for venting 

recommendations.

Prepare vent/chimney

•  Secure all metal vent joints with screws, following the vent manufacturer’s 

instructions. Seal all joints in the vent system and chimney. Repair ma-

sonry chimney lining and repair all mortar joints as needed.

•  Per ANSI Z21.8, install a double-acting barometric draft regulator in the 

vent piping. (The damper must be located in the same space as the 

appliance.) Install a manual reset spill switch on the draft regulator per 

instructions. Wire the switch into the appliance limit circuit to shut off the 

appliance/burner if sustained downdraft should occur. Refer to the appli-

ance manufacturer’s instruction manual for recommendations regarding 

the need for a barometric draft regulator.

•  Provide support for the vent piping. Do not rest the weight of any of the 

vent piping on the appliance flue outlet.

Figure 1

 

Vent and vent connector installations, typical

Summary of Contents for 601GAS































Reviews: