background image

Contents

PLEASE read this first ...........................................................2
Codes and standards ............................................................2
301GAS burner at-a-glance ...................................................3
Prepare site •  prepare burner •  mount burner .....................4
Install gas piping ..................................................................10
Wire burner ..........................................................................11
Check system  •  start-up burner/appliance .........................12
Perform checkout procedures  •  fill out certificate ..............14
Maintenance and service procedures ..................................16
Troubleshooting ...................................................................17
Dimensions and mounting information ................................19
Replacement parts ..............................................................20

Ratings

Input:

 

 .............................................401,000 to 1,100,000 Btuh

Fuels:

 

 ........................................... Natural gas or propane gas

 

Max. supply pressure .............................. 14 inches w.c.

 

Min. supply pressure ................................. 5 inches w.c.

 

Manifold pressure ................................... 3.5 inches w.c.

Electrical:

 Power ............................................120V/60 Hz/1-Phase

 Motor ................................1/6 HP, 3450 RPM, 1.8 amps
 

Total Current .......................................Approx. 2.5 amps

Ignition:

 

 ............................Carlin Model 41800 solid state ignitor

Control:

 

 ..............Carlin Model 60200FR microprocessor control

Agencies:

   ........................................................................UL  Listed  

  Installer/servicer — Except where specifically stated other-

wise, this manual must be used only by a qualified service 

technician. (In the state of Massachusetts, this product must 

be installed by a licensed Plumber or Gas Fitter.) Failure to 

comply with this or other requirements in this manual could 

result in severe personal injury, death or substantial property 

damage.

  User  — Refer only to User’s Information booklet for 

information regarding operation of this burner. The burner 

Instruction Manual is intended only for your service techni-

cian. The burner and heat exchanger must be inspected and 

started at least annually by your service technician.

126 Bailey Road 

North Haven, CT 06473

Ph  203-680-9401 

Fx  203-680-9403

Carlin Combustion Technology, Inc.

T

ech

 

support

   800-989-2275

carlincombustion.com

©

 

Copyright 2014 — Carlin Combustion Technology, Inc.

Instruction Manual

Summary of Contents for 301GAS

























Reviews: