Carl Valentin Vita II 103/8 T Page 31 Operating Manual Download

Page: 31 / 110

Vita II

Loading media

11.18

Operating manual

5.2 Loading fanfold labels

D C

Figure 10

1. Open the printer cover.

2. Open printhead (G) by turning the red pressure lever (F)

anticlockwise.

3. Load the fan-fold material from the back over the unwinding unit

(B).

4. Lead the fan-fold material below the return pulley (C) and the

printhead.
Pay attention that the label runs through the photocell (E).

5. In order to move the printhead (G) down, turn the red pressure

lever (F) in clockwise direction until it locks.

6. Adjust the adjusting ring (D) of the return pulley (C) and the label

mounting plate (A) to the width of material.

7. Close the printer cover.

Summary of Contents for Vita II 103/8 T















































































































Search results

Summary of Contents for Vita II 103/8 T

Reviews:

Related manuals for Vita II 103/8 T

Brands by name

Popular brands

Carl Valentin Vita II 103/8 T, Operating Manual

Search results

Summary of Contents for Vita II 103/8 T

Reviews:

Related manuals for Vita II 103/8 T

Brands by name

Popular brands