background image

2

TABLE OF CONTENTS

ADDITIONAL ITEMS REQUIRED . . . . . . . . . . . . . . . . . . . 2

  Radio Equipment  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
  Hardware and Accessories  . . . . . . . . . . . . . . . . . . . . . . 2
  Adhesives and Building Supplies . . . . . . . . . . . . . . . . . . 2
  Optional Supplies and Tools. . . . . . . . . . . . . . . . . . . . . . 2
PREPARATION  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

ASSEMBLE THE WING . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

INSTALL THE  FIN  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
INSTALL THE  STABILIZER. . . . . . . . . . . . . . . . . . . . . . . . 5
INSTALL THE RADIO SYSTEM  . . . . . . . . . . . . . . . . . . . . 5
FINISH THE  SAILPLANE  . . . . . . . . . . . . . . . . . . . . . . . . . 8

  Canopy Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
  Apply the Decals  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
GET THE MODEL READY TO FLY  . . . . . . . . . . . . . . . . . 11
  Check the Control Directions . . . . . . . . . . . . . . . . . . . . 11
  Set the Control Throws. . . . . . . . . . . . . . . . . . . . . . . . . 11
  Balance the Model (C.G.). . . . . . . . . . . . . . . . . . . . . . . 12
  Balance the Model Laterally . . . . . . . . . . . . . . . . . . . . . 13
CHECKING FOR WARPS  . . . . . . . . . . . . . . . . . . . . . . . . 13
PREFLIGHT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
  Identify Your Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
  Charge the Batteries  . . . . . . . . . . . . . . . . . . . . . . . . . . 13
  Ground Check & Range Check  . . . . . . . . . . . . . . . . . . 14

AMA SAFETY CODE. . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

  General  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
  Radio Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
CHECK LIST  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
FLYING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
  Mount the Wing  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
  Trim Flights. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
  Your First Hi-Start Launches  . . . . . . . . . . . . . . . . . . . . 16
  First Flights. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
  Thermal Flying . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
  Facts About Thermals  . . . . . . . . . . . . . . . . . . . . . . . . . 16
  Thermal Soaring  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
POINTERS FOR CONTEST FLYING. . . . . . . . . . . . . . . . 17
 Ballasting 

 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

ADDITIONAL ITEMS REQUIRED

RADIO EQUIPMENT 

The Sophisticated Lady ARF requires a two-channel radio 

system with standard size servos. The following servos are 
recommended. A square receiver battery or a small fl at receiver 
battery is required to fi t the narrow fuselage. 

 (2) Futaba

®

 S-3004 Standard Servo (FUTM0004)

  (1) HydriMax

 1600mAh NiMH fl at receiver battery 

(HCAM6308)

HARDWARE AND ACCESSORIES

Following is additional hardware and accessories required 
to fi nish the Sophisticated Lady ARF.  Order numbers are 

provided in parentheses. 

 1/4" Foam Rubber (GPMQ1000)

 #64 Rubber Bands (HCAQ2020)

ADHESIVES AND BUILDING SUPPLIES

In addition to common household and hobby tools, this is the 

“short list” of the most important items required to assemble 

the Sophisticated Lady ARF. Great Planes Pro

 CA glue is 

recommended. 

 Thin CA (1/2 oz. [15g] Thin Pro CA, GPMR6001)

  Medium CA (1/2 oz. [15g] Medium Pro CA+, 

GPMR6007)

  6-minute Pro Epoxy (4oz [113.4g] GPMR6042)

  30-minute Pro Epoxy (4oz [113.4g] GPMR6043)

 Mixing Sticks (GPMR8055)

 Epoxy Brushes (GPMR8060)

 Epoxy Mixing Cups (GPMR8056)

 Paper Towels

 Masking Tape

 CA applicator tips (HCAR3780)

 Threadlocker thread locking cement (GPMR6060)

 #11 blades (5-pack, RMXR6930)

 #1 Hobby knife (RMXR6900)

 #44 or 3/32" [2.4mm] drill bit

 Denatured Alcohol

 Wax Paper

 Needle-nose Pliers

OPTIONAL SUPPLIES AND TOOLS

Here is a list of optional tools mentioned in the manual that 
will help you build the Sophisticated Lady ARF.

 Stick–on segmented lead weight (GPMQ4485)

 Hobby paints/paint brushes for painting the pilot

 CA debonder (GPMR6039)

 CG Machine

 (GPMR2400)

 RC 56 Canopy Glue

 High Start (GPMP8015)

A model airplane covering iron with a protective covering 

sock may also be necessary to retighten the covering and 
remove any wrinkles that may have formed after the model 
was originally covered at the factory. If you don’t already have a 
covering iron, the 21

st

 Century

®

 sealing iron (COVR2700) and 

the 21

st

 Century iron cover (COVR2702) are recommended. 

Summary of Contents for Sophisticated Lady GPMA1959






















Reviews: