background image

‘Lightning’ 

Thank you very much for purchasing our CARF

-Models

 ‘

Ultra 

Lightning’, made with the 

revolutionary Total Area Vacuum Sandwich (TAVS) technology.

Please note that a few of the photos in this Instruction manual show certain views from the 3 pro-
totypes, so please don’t get confused by the different colour schemes!

Before you get started building and setting-up your aircraft, please make sure you have read this
instruction manual, and understood it. If you have any questions, please don’t hesitate to con-
tact your Rep, or C-ARF directly. Below are the contact details:

Email:

          [email protected]

Website

:      http://www.carf-models.com

Liability Exclusion and Damages

You have acquired a kit, which can be assembled into a fully working R/C model when fitted out
with suitable accessories, as described in the instruction manual with the kit.

However, as manufacturers, we at CARF

-Models

 are not in a position to influence the way you

build and operate your model, and we have no control over the methods you use to install,
operate and maintain the radio control system components. For this reason we are obliged to
deny all liability for loss, damage or costs which are incurred due to the incompetent or incorrect
application and operation of our products, or which are connected with such operation in any
way. Unless otherwise prescribed by binding law, the obligation of the CARF

-Models

 compa-

ny to pay compensation is excluded, regardless of the legal argument employed.

This applies to personal injury, death, damage to buildings, loss of turnover and business,
interruption of business or other direct and indirect consequent damages. In all circumstances
our total liability is limited to the amount which you actually paid for this model.

BY OPERATING THIS MODEL YOU ASSUME FULL RESPONSIBILITY FOR YOUR ACTIONS.

It is important to understand that CARF

-Models

 Co., Ltd, is unable to monitor whether you

follow the instructions contained in this instruction manual regarding the construction, operation
and maintenance of the aircraft, nor whether you install and use the radio control system
correctly. For this reason we at CARF

-Models

 are unable to guarantee, or provide, a

contractual agreement with any individual or company that the model you have made will
function correctly and safely. You, as operator of the model, must rely upon your own expertise
and judgement in acquiring and operating this model.

2

Summary of Contents for Ultra Lightning







































Reviews: