Carf-Models F4U-1D Corsair Page 42 Instructions Manual Download | Manualshive

Page: 42 / 45

background image

Page 42

Instruction Manual F4U-1D Corsair

CARF-Models Ltd. [email protected]

7. Paint and Finish

The surface of your Corsair with its silver top coat is almost ready to apply the final paint. Use a

ScotchBrite pad to roughen the surface slightly, just so that it breaks the shiny gloss. Use some

acetone or denaturized alcohol to clean the surface and remove any grease. Then tape off all

externally visible components or openings to protect the inside from any overspray. Of course,

remove engine and landing gear if you can. Do not use any primer!

Apply your scheme with any kind of 2 component polyurethane paint or base coat laquer. After

curing you should apply all trims and decals, before you finally shoot a very thin layer of flat clear

coat (or glossy, if the full scale plane you’re replicating is a restored and shiny bird).

Now you can scratch the panel lines with a screw driver or steel ruler, chip color off the leading

edge areas and around rivets and hatches, if you want to create a scale “patina” on your plane. The

silver top coat of the fiberglass parts will shine through and look like beat up aluminum. Finally

use a pad of ScotchBrite and rub the surface in flight direction. Add a little dust of black charcoal

powder while you’re doing this. The rest of patina will come by time…

Cut and shape the vacuum formed radiator intake details,
paint and glue them in. Use some tape to grip and pull
them firmly from inside against the radiator inlet

After trimming and painting
the canopy frame, you need
to fit the clear canopy to the
inside, preferrably in two pieces, front and rear. Use ZAP
canopy glue or 30 min epoxy. It is very important that you
tape the canopy on to the fuselage during curing, so that it
stays in undistorted shape.

«
...
40
41
42
43
44
...
»

Summary of Contents for F4U-1D Corsair














































Reviews:

No comments

Related manuals for F4U-1D Corsair

SM-79 Sparviero Exterior

Brand: Eduard Pages: 4

Brand: Faller Pages: 8

Golden Age Series

Brand: Rage Pages: 10

Grange Farm Tipper Wagon

Brand: Bole Laser Craft Pages: 6

Brand: Tumama Kids Pages: 30

Brand: J. Perkins Pages: 12

BEAR AND THE STARS

Brand: Chipolino Pages: 4

Spiderman 3 Unleashed 360 Web Spiderman 69168/69113

Brand: Hasbro Pages: 1

Follow Me Learning Squirrel

Brand: LeapFrog Pages: 12

Premier BL-2 Diesel Engine

Brand: Rail King Pages: 28

Brand: E sky Pages: 43

RailKing Steel Arch Bridge

Brand: MTHTrains Pages: 5

Brand: Faber Pages: 14

F-27D Evolution

Brand: Horizon Hobby Pages: 19

Brand: myToys Pages: 6

Brand: Agora Models Pages: 54

Brand: Fisher-Price Pages: 6

Super Étendard exterior

Brand: Eduard Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands