background image

Carefree of Colorado  

Installation Manual 

Mirage 

 1 

052979-003r5 

O

VERVIEW

 

G

ENERAL 

D

ESCRIPTION

 

The Mirage Patio Awning offers the coach owner an awning system that provides as much or as little shade 
as required.  The canopies are housed in an aluminum case that easily blends in with the coach side wall.  
The canopy is made from Sunbrella® fabric. 

Each unit is equipped with Mirage lateral support arms that are the strongest available on the market.  No 
vertical arms interfere with coach sidewalls or equipment that may be mounted on the sidewalls or sidewall 
graphics.  These arms can also be adjusted to vary the canopy pitch up to 2 feet (it is strongly 
recommended that service and adjustments be performed by trained technicians). 

The unique and innovative 110V electronic control system provides Carefree’s 

Direct Response

 system with 

interior pushbutton controls for standard extend/retract functions.  At the master control panel the auto-retract 
system can be engaged to automatically retract the awning in windy conditions.  Sensitivity can be set to respond 
to a variety of wind speed conditions.  An optional RF remote is available with the 

Direct Response

 system. 

Two configurations of the Mirage awning are available, a RH (passenger side) and a LH (driver’s side).  The motor 
is located to the front of the awning reducing wiring to keep the awning controls to the front of the vehicle.  In the 
Wiring Diagram the RH configuration is shown; detail A shows the alterations for the LH configuration. 

Mirage Patio Awning Specifications 

The following information is for reference only.  Specific information is detailed in the installation instructions. 

L

ENGTH

 

12’ – 21’ [3.66m - 6.4m] (in 1 foot [.305m] increments) 

E

XTENSION

10' [3m] 

D

ROP 

@

 

M

IN

.

 

P

ITCH

: 10" [25cm] 

D

ROP 

@

 

M

AX

.

 

P

ITCH

:

 

35" [89cm] 

 

 

Values are approximate, actual dimensions may vary with specific installations. 

S

UPPORT

Lateral Spring Arms  2 for 12' - 18'; 3 for 19' - 21' 

M

OTOR

Tubular 

Available in LH or RH configurations 

 

Power: 

120V, 60Hz, 2.5A 

Torque: 

60nm 

Speed: 

14 RPM 

C

ONTROLS

Direct Response

TM

 

C

OLOR

Hardware: 

White or Black 

 

Fabric: 

Woven Acrylic (refer to sales literature for colors) 

A

PPROXIMATE 

W

EIGHT 

(

LBS

.)

 

 

Awning Length  Weight 

Dim B 

Awning Length

Weight

Dim B 

Awning Length  Weight  Dim B 

12 134 

6.5in 15 160 

11.25in

19 194 

17in 

13 143 

16 169 

20 203 

14 152 

17 177 

21 211 

  

 

18 

186 

22 

220 

6 3/8"

8"

1 1/4"

5.57"

B

B

Lateral Arm Mount (ref)

(Awning Length)

Back Plate (Awning Case)

Mounting Plate (ref)

3" (ref)

MIRAGE007a

1 1/2" (ref)

 

Figure 1.  General Description - Mirage Patio Awning. 

Summary of Contents for MIRAGE
















Reviews: