background image

L

ATITUDE

 Service 

Manual 

Carefree of Colorado 

070005-301r5 

R

EPLACING THE 

M

OUNTING 

P

LATE

 

This procedure requires two people.  The illustrations show 
the RH plate.  The procedure is the same for the LH plate. 

1.  Open the awning 18"-24".  This is to allow adequate 

room for tools and access to the mounting plate. 

2. Disconnect 

power. 

3.  Do not remove the bottom inner screw and the outer 

upper screw marked with * in the illustration.  Remove 
the rest of the plate fasteners and set aside. 

4.  On the side being repaired: 

4.1. Collapse the arm.  Leave a space between the arm 

and plate to access the set screw in later steps. 

4.2. Securely tie the arm channels together with zip 

ties.  The ties should be close to the head. 

5.  Have a second person hold and support the roller tube 

and arm at the arm elbow. 

6.  For the motor side mounting plate: 

NOTICE  

If replacing the plate on the motor side, use care to not pull or damage the cable. 

6.1. 

If the motor cable is routed into the vehicle outside of the plate:

  Partially remove the wire from the 

top of the arm channel to provide adequate slack to move the cable out of the way. 

6.2. 

If the motor cable and LED harness are routed through a hole in the plate:

  Pull some slack cable 

out of the wall and cut the wires.  It will be necessary to splice the wires together after the new 
plate is installed. 

7.  Remove the two remaining screws in the mounting plate and rotate the arm and plate away from the wall. 

8.  Loosen the set screw and remove the rotation pin that attaches the arm to the plate.  Set plate aside. 

9.  Attach the arm to the new plate using the rotation pin removed previously.  Tighten the set screw to 

secure the pin. 

10. Using the existing mounting holes in the wall, attach the new plate to the wall with a minimum of 2 

screws in the bottom inner screw position and the outer upper screw position. 

11. Remove the arm ties and allow the roller tube to slowly extend out. 

 

 

CAUTION

  

Firmly hold the arm while removing the ties.  When the arm is closed, it can open 

with significant force. 

12. Install the remaining plate fasteners. 

13. For the motor side mounting plate: 

13.1. 

If the motor cable is routed into the vehicle outside of the plate:

  Insert the motor cable into the 

groove in the top of the arm channel. 

13.2. 

If the motor cable and LED harness are routed through a hole in the plate:

  Use appropriate sized 

butt connectors to attach motor cable and LED wires that were cut previously.  Be sure to match 
the wire colors. 

Wire 

Wire Gauge 

Butt Connector Size 

Red and Black LED wires 

24awg 

22-24 awg 

Red and Black Power 

16awg 

14-16 awg 

Brown, Yellow and Gray 

20awg 

18-22 awg 

13.3.  Push the connectors into the wall and seal the hole with a quality silicone sealant. 

14. Check that the arm is properly aligned with the roller tube.  Refer to "Adjusting the Arm Position" on page 1. 

15. Extend the awning and check the pitch.  To adjust the arm pitch refer to "Adjusting the Pitch" on page 1. 

Set Screw

Rotation
Pin

Control

Cable

FL026

Mounting
Plate

Fasteners (x9)

*

 Remove these fasteners last from old plate;

   Attach these fasteners first with new plate

Tie Arm Together

4"

Summary of Contents for LATITUDE





















Reviews: