background image

052567-001r5 

Printed in USA 

September, 2016 

 

C

AREFREE

 

T

RAVEL

'

D

IRECT 

R

ESPONSE

A

UTO

-R

ETRACT 

S

YSTEM

 

 

The Travel'r Direct Response Auto-Retract System may be installed as part of the original Travel'r awning 
installation or as an upgrade to an existing awning installation. 

 

 

 

 

 

 

 

 

 

 

 

 

T

ABLE OF 

C

ONTENTS

 

Prior to Installing the Kit ................................................................................................................................ 3

 

Installing the Sensor ..................................................................................................................... 4

 

Switch Installation ......................................................................................................................... 7

 

Wiring an Additional Extend/Retract Switch ................................................................................................. 8

 

Attach the Label ............................................................................................................................ 8

 

 

 

Read this manual before installing or using this product.  Failure to follow the instructions 
and safety precautions in this manual can result in personal injury and/or cause the 
product to not operate properly. 

Carefree of Colorado 

2145 W. 6

th

 Avenue Broomfield, CO  80020 

a

 Scott Fetzer 

company

 

Summary of Contents for DIRECT RESPONSE









Reviews: