background image

10 

Part number 3E1100 R16 

 

July 2010 

 

Approvals and Standards 

FCC 

This equipment has been tested and found to comply with the limits for a Class B digital 
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide 
reasonable protection against harmful interference in a residential installation. This 
equipment generates, uses and can radiate radio frequency energy and, if not installed 
and used in accordance with the instructions, may cause harmful interference to radio 
communications. However, there is no guarantee that interference will not occur in a 
particular installation. 

If this equipment does cause harmful interference to radio or television reception, which 
can be determined by turning the equipment off and on, the user is encouraged to try to 
correct the interference by one or more of the following measures: 

 

Reorient or relocate the receiving antenna. 

 

Increase the separation between the equipment and receiver. 

 

Connect the equipment into an outlet on a circuit different from that to which the 
receiver is connected. 

 

Consult the dealer or an experienced radio/TV technician for help. 

Note: 

Changes or modifications not expressly approved by Gallagher Group Limited 

could void the user's authority to operate the equipment. 

 

For UL Installations:

 

Refer to the section in the Cardax FT Command Centre Installation Note, 

"Configuration Instructions to meet Underwriters Laboratory Inc Approved 
Installations"

 for details covering specific requirements necessary to meet the specified 

UL Licences.  The following Release Note version(s) contain these details: 
vEL5.21.xxx  May 2009  
vEL6.01.xxx October 

2009 

Installers must ensure these instructions are followed to ensure the installed system is 
UL compliant. 
UL temperature range tested and certified from -35

0

C - +66

0

C . 

The voltage current values used and measured during testing are shown in the table 
“Voltage / Current measurements” included in the Cardax FT Command Centre 
Installation Note, 

"Configuration Instructions to meet Underwriters Laboratory Inc 

Approved Installations"

.

 

 

Summary of Contents for Prox Mifare Series













Reviews: