Car-Interface CI-RL4-SY3-R5 Manual Download

Page: 1 / 26

Version 30.12.2021

HW: CAM(V100)/(V11+V41)

ab Serien Nr: NZ20NOV694

CI-RL4-SY3-R5

Video-inserter

CI-RL4-SY3-R5

Compatible with Ford vehicles with

Sync3 Light (R5) version

with 6.5, 7 or 8inch tablet monitor

Sync Connected Radio version

with 4inch monitor

Video-inserter for front- and rear-view camera

and two additional video sources

Product features



Video-inserter for factory-infotainment systems



1 CVBS Input for rear-view camera



1 CVBS Input for front camera



2 CVBS video-inputs for after-market devices (e.g. USB-Player, DVB-T2 tuner)



Automatic switching to rear-view camera input on engagement of the reverse gear



Automatic front camera switching after reverse gear for 10 seconds



Activatable parking guide lines for rear-view camera (not available for all vehicles)



Video-in-motion (ONLY for connected video-sources)



Video-inputs NTSC and PAL compatible

Summary of Contents for CI-RL4-SY3-R5



























Search results

Summary of Contents for CI-RL4-SY3-R5

Reviews:

Related manuals for CI-RL4-SY3-R5

Brands by name

Popular brands

Car-Interface CI-RL4-SY3-R5, Manual

Search results

Summary of Contents for CI-RL4-SY3-R5

Reviews:

Related manuals for CI-RL4-SY3-R5

Brands by name

Popular brands