Car-Interface CI-RL4-MBN6 Manual Download

Page: 1 / 26

Version 22.10.2021

HW:CAM(V98/99/100)/(V45/46)

CI-RL4-MBN6

Video inserter

CI-RL4-MBN6

Compatible with Mercedes Benz vehicles with

MBUX/NTG6 with 7inch or 10.25inch monitor

Video-inserter for front- and rear-view camera

and two more video inputs

Product features



Video-inserter for factory-infotainment systems



1 CVBS Input for rear-view camera



1 CVBS Input for front camera



2 CVBS Video-inputs for after-market Video sources (e.g. DVD-Player, DVB-T Tuner)



Automatic switching to rear-view camera input on engagement of the reverse gear



Automatic front camera switching after reverse gear for 10 seconds



Activatable parking guide lines for rear-view camera for 7inch monitors (not
available for all vehicles)



Video-in-motion (ONLY for connected video-sources)



Video-inputs NTSC and PAL compatible

Summary of Contents for CI-RL4-MBN6



























Search results

Summary of Contents for CI-RL4-MBN6

Reviews:

Related manuals for CI-RL4-MBN6

Brands by name

Popular brands

Car-Interface CI-RL4-MBN6, Manual

Search results

Summary of Contents for CI-RL4-MBN6

Reviews:

Related manuals for CI-RL4-MBN6

Brands by name

Popular brands