Car-Interface CI-RL2-SC14 Manual Download

Page: 1 / 20

Version 04.05.2021

CAM(V31)9275&9276(V11)

CI-RL2-SC14

r.LiNK

Video-inserter

CI-RL2-SC14

Compatible with

Volvo vehicles with Sensus Connect Infotainment and internet button

with 7 inch monitor

Video-inserter for rear-view camera

and two additional video sources

Product features



Video-inserter for factory-infotainment systems



2 CVBS video-inputs for after-market devices (e.g. DVD-Player, DVB-T tuner)



FBAS Rear-view camera video-input



Automatic switching to rear-view camera input on engagement of the reverse gear



Activatable parking guide lines for rear-view camera (not for all vehicles)



Picture-in-picture (PIP) mode combining after-market rear-view camera picture
with factory parking sensor graphic (not for all vehicles)



Video-in-motion in drive mode (ONLY for connected video-sources)



Video-inputs NTSC and PAL compatible

Summary of Contents for CI-RL2-SC14





















Search results

Summary of Contents for CI-RL2-SC14

Reviews:

Related manuals for CI-RL2-SC14

Brands by name

Popular brands

Car-Interface CI-RL2-SC14, Manual

Search results

Summary of Contents for CI-RL2-SC14

Reviews:

Related manuals for CI-RL2-SC14

Brands by name

Popular brands