background image

Capstone Turbine Corporation 

Model C65 Hybrid UPS User’s Manual 

 

 

400027 Rev A (July 2010) 

Page 

9 of 66 

Capstone reserves the right to change or modify, without notice, the design, specifications, and/or contents of this document without 

incurring any obligation either with respect to equipment previously sold or in the process of construction. 

 

General Precautions 

The following general precautions must be observed and followed at all times. Failure to 
do so may result in personal injury and/or equipment damage. 

NOTE 

Some of the following precautions do not directly apply to users, but it is 
important for users to be aware of them. 

 

 

Only Capstone Authorized Service Providers are permitted access to the 
inside of the enclosure. 

  Read and understand the User's Manual before operating the equipment. 

  Read and obey all warnings and cautions. 

  Make sure all fuel connections are tight, free from leaks, and protected from 

damage. 

  Make sure all electrical connections are tight, clean, dry, and protected from 

weather and damage. 

  The MicroTurbine may be equipped with a heat recovery system.  Use caution 

around relief valves where hot water and steam may be present. 

  Use hearing protection when you work on or near an operating  MicroTurbine  for 

extended time periods. 

  The MicroTurbine is heavy. Be careful when you move or lift the MicroTurbine. 

  Keep the equipment clean. 

  Keep all flammable materials away from the MicroTurbine and its components. 

  Do not operate or work on the equipment if mentally or physically impaired, or after 

consumption of alcohol or drugs. 

  Make sure all fasteners are installed and properly tightened. 

  Keep an ABC rated fire extinguisher near the MicroTurbine. 

  Obey all applicable local, state, and national codes and regulations. 

Electrical Precautions 

WARNING 

The MicroTurbine system contains and produces high voltage. High 
voltage can injure or kill. Obey all safety procedures when you work 
around electrical equipment. 

 

WARNING 

Make sure the system is off and the dedicated disconnect switch is in 
the open position and is locked. This will help prevent injury and damage 
to the equipment. 

 

NOTE 

Some of the following precautions do not directly apply to users, but it is 
important for users to be aware of them. 

Summary of Contents for MicroTurbine C65



































































Reviews: