background image

Capstone Turbine Corporation 
Model C65 Hybrid UPS User’s Manual 

 

 

Page 

34 of 66 

400027 Rev A (July 2010)

 

Capstone reserves the right to change or modify, without notice, the design, specifications, and/or contents of this document without 

incurring any obligation either with respect to equipment previously sold or in the process of construction. 

 

Using the UPS Controller 

The Capstone UPS Controller is required for any application with more than one Hybrid 
UPS microturbine. The Capstone UPS Controller accessory acts as a master for up to ten 
Hybrid UPS microturbines, and coordinates MultiPac operation to provide high availability 
of power to the critical load. 

The UPS Controller can: 

  Display overall system status as well as details for individual microturbines. 

  Start and Stop the system and change the desired operating modes. 

  Communicate with a Building Management System to share monitored 

microturbine data, accept power demand and other control commands, and signal 
potential shutdown conditions. 

  Coordinate Hybrid UPS microturbine state transitions, including consideration of 

external battery state of charge information. 

  Provide a common communications connection for a PC with CRMS software. 

Figure  4  shows the typical connections available from the UPS Controller. Refer to the 
UPS Controller User Manual (400028) for a complete description of this accessory and 
how to operate it. 

Hybrid UPS

UPS Controller

10 Base2 COAX

Intra Cable* 

10 BaseT Ethernet

Hybrid UPS

110-220 Vac

PC (CRMS)

System Wakeup, 

Start/Stop, Fast Stop. 

Transfer Switch Status

Shutdown Alarms

Discrete I/O

Analog In

Modbus TCP/IP

* the Intra Cable provides three 
twisted pair between microturbines, 
and two twisted pair to the UPS 
Controller

 

Figure 4. UPS Controller External Connections 

 

Summary of Contents for MicroTurbine C65



































































Reviews: