background image

5

Instruction manual PH500H

Please keep this instruction manual for future reference 

E N V I R O N M E N TA L   P R OT E C T I O N    

Waste electrical products should not be disposed of with household waste. Please recycle 
where facilities exist. Check with your Local Authority or retailer for recycling advice. This 
appliance is marked according to the European Directive on Waste Electrical and Electronic 
Equipment (WEEE).

By ensuring this product is disposed of correctly, you will help prevent potential negative 
consequences for the environment and human health, which could otherwise be caused 
by inappropriate waste handling of this product. The symbol on the product indicates that 
this product may not be treated as household waste. Instead it shall be handed over to the 
applicable collection point for the recycling of electrical and electronic equipment. Disposal 
must be carried out in accordance with local environmental regulations for waste disposal.

For more detailed information about treatment, recovery and recycling of this product, please 
contact your local council, your household waste disposal service or the retailer where you 
purchased the product.

C E   D E C L A R AT I O N S   O F   C O N F O R M I T Y  

This appliance has been manufactured to the strictest standards and complies with all 
applicable legislation, Low Voltage Directive (LVD) and Electromagnetic Compatibility (EMC).

U K C A   D E C L A R AT I O N S   O F   C O N F O R M I T Y  

 

This appliance has been manufactured to the strictest standards and complies with all  
applicable legislation. 

WA R R A N T Y

Your new appliance is covered by warranty. The warranty card is enclosed - if it is missing, you 
must provide the following information to your retailer in order to receive a replacement: date 
of purchase, model and serial number (placed on the inside of the appliance storage drawer). 
Registration can also be completed online by visiting www.caple.co.uk. 
Ensure you keep your warranty card safe, you may need to show it to Caple Service together 
with proof of purchase.  
If you fail to show your warranty card you will incur all repair charges.  
Spare parts are only available from Caple Service and spare parts authorised centres.

Summary of Contents for PH500H













Reviews: