7
WORKING
sequentially by turning the knob ; the desired
function is set by pressing the knob.
- LIGHTS Indicator (fig. 18C)
This function allows you to switch the lights
on or off; turn the rotary control until the
function is selected, then set it by pressing
the rotary control.
- Timer Indicator (fig. 18D)
By setting this control, at any speed, the
appliance will be switched off after 10
minutes. It is necessary to select the control
again in order to exit from this function. .
When the Timer function is set , the Timer
indicator will flash and the corresponding
speed indicator is lit.
- Speed Indicators (fig. 18E)
They are lit accordingly to the speed set.
OFF
Indicator (Fig.18F): This function allows
you to completely switch off the motor; it is
totally lit during selection and setting, while
it is in standby afterwards.
MOT901 - MOT912 Mode
l (fig. 19)
This model, in addition to the working
features described in the paragraph above,
has an automatic opening and closing
system of the glass panel.
The opening of the glass panel corresponds to
and
varies
according
to
the
motor
speed
set.
The
panel
is
closed
automatically,
after
the
motor
is
switched
off.
A safety device reverses the panel direction in
case
of
impact
with
unusual
surfaces
during
its
normal
travel.
All
of
the
appliances are equipped with an
electronic
device
allowing
for
automatic
switching off
after
four
hour
working
from
the
last
operation
performed.
Touch control
(fig. 20
)
A: Light switch On/Off
B:
Reduce
speed
/
OFF
motor
C:
Motor speed display
D:
ON
motor/incr
e
ase speed
E:
10
-
minute
timer
The touch control key allows the function
desired by touching the relative key.
If the electrical power supply to the product is
cut, 15 seconds are needed for self
diagnostics after the functions are restored.
In
the
meanwhile, its operation may be
incorrect.
(fig. 13), then disconnect the bipolar
elec
t
ric
connector. Insert the screw anchors
and screws provided in the holes indicated by
the arrows (fig. 14).
If the appliance is installed in the
external
extraction mode
, remove the grid covering the
motor air outlet (fig. 15).
Reinsert the grease filter and the light front
panel, making sure the electric connector is
connected properly.
ZZ801 MODEL ONLY
After the appliance is adjusted, fix it by
inserting and tightening the safety screws
properly (fig.16).
External extraction mode
Using the supplied wall plugs and screws, fix
the tube support bracket (Des. 10) to the wall
and/or the ceiling. The bracket must be fixed
in a central position in respect of the air
outlet flange.
Connect the motor air
outlet flange to the
exhaust hole, by using a suitable pipe.
Perform the electric connection. Place the
two ornamental pipes on the hood body; lift
the internal pipe up until it reaches the
ceiling; then fix it to the pipe bearing
bracket, by using the two self
threaded
screws provided.
Perform the electric connection.
* Filtering version
Fix the air deflector to the pipe bearing
bracket, by using the screws provided.
Fix the pipe bearing bracket to the wall and/
or ceiling (Fig.17), cent
e
red to the hood.
Connect the motor air
outlet flange to the air
deflector, by using a suitable pipe. Perform
the electric connection. Place the two
ornamental pipes on the hood body; lift the
internal pipe up until it reaches the ceiling;
then fix it to the pipe bearing bracket, by
using the two self
threaded screws provided.
LUC600 - MOT901 Model (fig. 18)
The rotary knob (fig. 18A) allows you to select
the various functions of the appliance.
All the indicators (fig. 18B) are always lit in
the standby function ; functions are selected
Summary of Contents for LUC600
