background image

Page 

C210 user manual.doc 

 

ELECTRICAL REQUIREMENTS 

This  Installation  should  be  carried  out  by  a  competent 
electrician in accordance with current I.E.E. Regulations. 
This  CAPLE  product  must  be  connected  to  an  electricity 
supply at the voltage shown on the rating plate. Connection 
must  be  made  via  a  double  pole-isolating  switch  with  a 
contact separation of at least 3mm. 
Use  supply  cable,  having  a  minimum  conductor 
cross-sectional area of 1.25 mm2. 
Where  both  hob  unit  and 

an  oven  are  to  be  installed 

adjacent  to  each  other,  both  appliances  may  be 
supplied via the 

same double pole-isolating switch using 

separate supply cables. Check that the total loading of the installation is within the capacity 
of the double pole isolating switch and the supply circuit. 
Allow  sufficient  length  in  the  supply  cable(s)  for  removal  of  the  appliance(s)  for  any 
subsequent servicing. Ensure that this extra cable is not trapped and is not in contact with 
the underside of any hob when fitting the appliance(s) in position. 
As with all electrical appliances always switch off the electricity supply when not in use for 
long periods (when on holiday) and before attempting any maintenance task. 
 

Fitting Into position 

Your new CAPLE oven is designed to fit into a kitchen unit, which is at least 550 mm deep. 
Before proceeding with the installation, check that the oven will fit into the space intended 
for it, appropriate ventilation slots are provided as per installation instructions on page 5 and 
that all packing material has been removed. 
 

IMPORTANT 

Materials used to build the oven housing must be capable of withstanding temperatures of 
up to 100°C and the housing must be firmly fixed in position. 
 

 

WARNING! 

ELECTRICITY CAN BE 

EXTREMELY 

DANGEROUS. 

THIS APPLIANCE 

MUST BE 

EARTHED. 

 

Before Use

 

 

Check that all accessories have been removed from the oven interior. 

 

Set the temperature to 225°C using the temperature control knob. 

 

Leave on for approximately 30 minutes. This will burn off any protective coating applied 
to the oven during manufacture. 

 

The kitchen should be well ventilated during this time as there may be an odor given off. 

 

When cool, wash the accessories and the oven with warm water and mild detergent.

 

Summary of Contents for LIBERTY C210 F/A















Reviews: