Instruction manual CM130
14
Please keep this instruction manual for future reference
Hub (underside)
Glass tray
Turntable ring assembly
a.
Never place the glass tray upside down.
The glass
tray should never be
restricted.
b.
Both
the
glass tray and turntable ring
assembly
must
always be used during
cooking.
c.
All food and containers of food
must
always
be
placed
on the glass tray for
cooking.
d.
If glass tray or turntable ring assembly
cracks or
breaks, contact your nearest
authorized
Caple
service
center.
Turntable Installation
Turntable shaft
The accessible surface
may be hot during
operation.
Installation and connection
1.This appliance is only intended for domestic use.
The guarantee is void if used in
any commercial application.
2.This oven is intended for built-in use only.
It is not intended for counter-top use or for
use inside a cupboard.
3. Please observe the
detailed
installation instructions.
4.The appliance can be installed in a 60cm wide wall-mounted cupboard
(at leas
t
55cm
deep and 85cm off the floor).
5.The appliance is fitted with a plug and must only be connected to a properly installed
earthed socket.
6.The mains voltage must correspond to the voltage specified on the rating plate.
7.The socket must be installed and connecting cable must only be replaced by a
qualified electrician.If the plug is no longer to accessible following installation,an
all-pole disconnecting device must be present on the installation side with a contact
gap of at lease 3mm.
8.Adapters,multi-way strips and extension leads must not be used. Overloading can
result in a risk of fire.
10
I N S TA L L AT I O N
T U R N TA B L E I N S TA L L AT I O N
› Never place the glass tray upside down. The glass
tray should never be restricted.
› Both the glass tray and turntable ring assembly must
always be used during cooking.
› All food and containers of food must always be
placed on the glass turntable for cooking.
› If glass tray or turntable ring assembly cracks or
breaks, contact your nearest authorised Caple
Service centre.
I N S TA L L AT I O N A N D C O N N E C T I O N
› This appliance is only intended for domestic use. The guarantee is void if used in any
commercial application.
› This oven is intended for built-in use only. It is not intended for counter-top use or for use inside
a cupboard.
› Please observe the detailed installation instructions.
› The appliance can be installed in a 60cm wide wall-mounted cupboard (at least 55cm deep and
85cm off the floor).
› The appliance is fitted with a plug and must only be connected to a properly installed
earthed socket.
› The mains voltage must correspond to the voltage specified on the rating plate.
› The socket must be installed and the connecting cable must only be replaced by a qualified
electrician. If the plug is no longer accessible following installation, an all-pole disconnecting
device must be present on the installation side with a contact gap of at lease 3mm.
› Adapters, multi-way strips and extension leads must not be used. Overloading can result in a
risk of fire.
WARNING:
The accessible surface may be hot during operation.
Hub (underside)
Glass tray
Turntable ring assembly
a.
Never place the glass tray upside down.
The glass
tray should never be
restricted.
b.
Both
the
glass tray and turntable ring
assembly
must
always be used during
cooking.
c.
All food and containers of food
must
always
be
placed
on the glass tray for
cooking.
d.
If glass tray or turntable ring assembly
cracks or
breaks, contact your nearest
authorized
Caple
service
center.
Turntable Installation
Turntable shaft
The accessible surface
may be hot during
operation.
Installation and connection
1.This appliance is only intended for domestic use.
The guarantee is void if used in
any commercial application.
2.This oven is intended for built-in use only.
It is not intended for counter-top use or for
use inside a cupboard.
3. Please observe the
detailed
installation instructions.
4.The appliance can be installed in a 60cm wide wall-mounted cupboard
(at leas
t
55cm
deep and 85cm off the floor).
5.The appliance is fitted with a plug and must only be connected to a properly installed
earthed socket.
6.The mains voltage must correspond to the voltage specified on the rating plate.
7.The socket must be installed and connecting cable must only be replaced by a
qualified electrician.If the plug is no longer to accessible following installation,an
all-pole disconnecting device must be present on the installation side with a contact
gap of at lease 3mm.
8.Adapters,multi-way strips and extension leads must not be used. Overloading can
result in a risk of fire.
10
